Digi 90000797_A manual Digi Connect Wi- Wave module edge connector Pinout

Page 9

Digi Connect Wi- Wave module edge connector: Pinout

..

What’s on the module?.. .

The module edge connector is configured as shown (signal direction w.r.t Wi-Wave):

Pin	Type	WLAN Mini Card	Pin	Type	WLAN Mini Card
		signal			signal

1	n/a	No connect	2	In	Vcc_3.3

3	n/a	No connect	4	In	GND

5	n/a	No connect	6	n/a	No connect

7	n/a	No connect	8	n/a	No connect

9	In	GND	10	n/a	No connect

11	n/a	No connect	12	n/a	No connect

13	n/a	No connect	14	n/a	No connect

15	In	GND	16	n/a	No connect

		Key			Key

17	n/a	No connect	18	In	GND

19	n/a	No connect	20	In	W_DISABLE#

21	In	GND	22	In	RESET (PERST#)

23	n/a	No connect	24	n/a	No connect

25	n/a	No connect	26	In	GND

27	In	GND	28	n/a	No connect

29	In	GND	30	n/a	No connect

31	n/a	No connect	32	n/a	No connect

33	n/a	No connect	34	In	GND

35	In	GND	36	I/O	USB_D-

37	n/a	No connect	38	I/O	USB_D+

39	n/a	No connect	40	In	GND

41	n/a	No connect	42	Out	LED_WWAN#

43	n/a	No connect	44	Out	LED_WLAN#

45	Rsvd (In)	JTAG_TCK	46	Out	LED_WPAN#

47	Rsvd (In)	JTAG_TMS	48	n/a	No connect

49	Rsvd (Out)	JTAG_TDO	50	In	GND

51	Rsvd (In)	JTAG_TDI	52	In	Vcc_3.3

U.FL connectors The module uses two U.FL antenna connectors (P1 and P2) to allow for cabling to embedded antennas or external antenna connectors. For more information, see Chapter 3, “Using the Antenna.”

www.digiembedded.com

11

Image 9

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B G i i n f o r m a t i o n UpdatesRelated DocumentationTo contact Digi International by Use Contact informationA t u r e s About the ModuleA t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connectorPin Type Wlan Mini Card Signal Digi Connect Wi- Wave module edge connector Pinout2 1 b / g m o d e s a n d c h a n n e l s B p e r i p h e r a l c o n t r o l l e rChannel Allocations Channel Center frequency Frequency spread MHz MHz MHzL t a g e m o n i t o r R e s e t g e n e r a t o r L t a g e r e g u l a t o r sW e r A t ’ s o n t h e d e v e l o p m e n t b o a r d FeaturesDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 No connect or Jtagtdi Vcc3.3 Pin Type SignalD s Debug signal breakout header LEDsAlternative methods to trigger I t c h e s a n d r e s e t f u n c t i o n a l i t yW e r s u p p l y Input power jack, J3 Input power supplyHeader signal map A G B r e a k o u t H e a d e r , P 2Jtag breakout B p e r i p h e r a l i n t e r f a c e , J Debug breakout Header signal map SignalB u g b r e a k o u t h e a d e r , P 2 FL connectors L a n d R P S M a c o n n e c t o r sFL cables RP-SMA connectors For more information Necessary Conditions for Integration Using the AntennaConnect Wi-Wave antenna configurations Dimensions T e n n a Specification s 2 d B i D i p o l eN e r a l i n f o r m a t i o n AttributesAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram Attribute Band T e n n a Specification s 5 d B i D i p o l eColor Freq MHz Peak dBi Angle o Avg dBi Radiation pattern H-Plane 2.0 and 5.0 GHzRadiation pattern E-plane 2.0 and 5.0 GHz C h a n i c a l d i m e n s i o n s V i r o n m e n t a l Specification sE x p o s u r e s t a t e m e n t W e r r e q u i r e m e n t sF e t y s t a t e m e n t s Parameter LimitsModule Dimensions Development Board dimensions C P a r t 1 5 C l a s s B Appendix BCertificationsModifications FCC Declaration of Conformity Standards International EMC StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008