Digi 90000797_A manual Appendix BCertifications, C P a r t 1 5 C l a s s B

Page 37

Appendix B:Certifications

The Digi Connect Wi-Wave products comply with the standards cited in this section.

F C C P a r t 1 5 C l a s s B

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Radio Frequency Interface (RFI) (FCC 15.105)

The Digi Connect Wi-Wave embedded module has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Labeling Requirements (FCC 15.19)

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this

39

Image 37

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B G i i n f o r m a t i o n UpdatesRelated DocumentationTo contact Digi International by Use Contact informationA t u r e s About the ModuleA t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connectorPin Type Wlan Mini Card Signal Digi Connect Wi- Wave module edge connector Pinout2 1 b / g m o d e s a n d c h a n n e l s B p e r i p h e r a l c o n t r o l l e rChannel Allocations Channel Center frequency Frequency spread MHz MHz MHzL t a g e m o n i t o r R e s e t g e n e r a t o r L t a g e r e g u l a t o r sW e r A t ’ s o n t h e d e v e l o p m e n t b o a r d FeaturesDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 No connect or Jtagtdi Vcc3.3 Pin Type SignalD s Debug signal breakout header LEDsAlternative methods to trigger I t c h e s a n d r e s e t f u n c t i o n a l i t yW e r s u p p l y Input power jack, J3 Input power supplyA G B r e a k o u t H e a d e r , P 2 Header signal mapJtag breakout B p e r i p h e r a l i n t e r f a c e , J Signal Debug breakout Header signal mapB u g b r e a k o u t h e a d e r , P 2 L a n d R P S M a c o n n e c t o r s FL connectorsFL cables RP-SMA connectors For more information Necessary Conditions for Integration Using the AntennaConnect Wi-Wave antenna configurations Dimensions T e n n a Specification s 2 d B i D i p o l eN e r a l i n f o r m a t i o n AttributesAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram Attribute Band T e n n a Specification s 5 d B i D i p o l eColor Freq MHz Peak dBi Angle o Avg dBi Radiation pattern H-Plane 2.0 and 5.0 GHzRadiation pattern E-plane 2.0 and 5.0 GHz C h a n i c a l d i m e n s i o n s V i r o n m e n t a l Specification sE x p o s u r e s t a t e m e n t W e r r e q u i r e m e n t sF e t y s t a t e m e n t s Parameter LimitsModule Dimensions Development Board dimensions C P a r t 1 5 C l a s s B Appendix BCertificationsModifications FCC Declaration of Conformity Standards International EMC StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008