Digi 90000797_A manual A G B r e a k o u t H e a d e r , P 2, Jtag breakout, Header signal map

Page 20

A B O U T T H E D E V E L O P M E N T B O A R D

JTAG Breakout Header, P20

cable to the development board. However, Digi recommends using the supplied AC wall adapter.

J T A G B r e a k o u t H e a d e r , P 2 0

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

JTAG breakout	The development board provides a 20-pin JTAG header, P20. The pins are allocated
header signal map	as shown:

	Pin	Type	Signal		Pin	Type	Signal

	1	Monitor pt	+3.3V		2	Monitor pt	+3.3V

	3	n/a	No connect		4	Monitor pt	GND

	5	In	JTAG TDI		6	Monitor pt	GND

	7	In	JTAG TMS		8	Monitor pt	GND

	9	In	JTAG TCK		10	Monitor pt	GND

	11	n/a	No connect		12	Monitor pt	GND

	13	Out	JTAG TDO		14	Monitor pt	GND

	15	In	RST# TRIGGER		16	Monitor pt	GND

	17	n/a	No connect		18	Monitor pt	GND

	19	n/a	No connect		20	Monitor pt	GND

22	Connect Wi-Wave Hardware Reference, Rev A 2/2008

Image 20

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Updates G i i n f o r m a t i o nRelated DocumentationContact information To contact Digi International by UseAbout the Module A t u r e sDigi Connect Wi- Wave module edge connector A t ’ s o n t h e m o d u l e ?Digi Connect Wi- Wave module edge connector Pinout Pin Type Wlan Mini Card SignalB p e r i p h e r a l c o n t r o l l e r 2 1 b / g m o d e s a n d c h a n n e l sChannel Allocations Channel Center frequency Frequency spread MHz MHz MHzL t a g e r e g u l a t o r s L t a g e m o n i t o r R e s e t g e n e r a t o rW e r Features A t ’ s o n t h e d e v e l o p m e n t b o a r dDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 Pin Type Signal No connect or Jtagtdi Vcc3.3Debug signal breakout header LEDs D sI t c h e s a n d r e s e t f u n c t i o n a l i t y Alternative methods to triggerInput power jack, J3 Input power supply W e r s u p p l yJtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Using the Antenna Necessary Conditions for IntegrationConnect Wi-Wave antenna configurations T e n n a Specification s 2 d B i D i p o l e DimensionsN e r a l i n f o r m a t i o n AttributesAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram T e n n a Specification s 5 d B i D i p o l e Attribute BandRadiation pattern H-Plane 2.0 and 5.0 GHz Color Freq MHz Peak dBi Angle o Avg dBiRadiation pattern E-plane 2.0 and 5.0 GHz V i r o n m e n t a l Specification s C h a n i c a l d i m e n s i o n sW e r r e q u i r e m e n t s E x p o s u r e s t a t e m e n tF e t y s t a t e m e n t s Parameter LimitsModule Dimensions Development Board dimensions Appendix BCertifications C P a r t 1 5 C l a s s BModifications FCC Declaration of Conformity International EMC Standards StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008