Digi 90000797_A manual Radiation pattern E-plane 2.0 and 5.0 GHz

Page 32

U S I N G T H E A N T E N N A

End User Manual: RF Exposure Statements

Radiation pattern: E-plane (2.0 and 5.0 GHz)

Color	Freq (MHz)	Peak (dBi)	Angle (o)	Avg (dBi)

Yellow	2400.0	2.60	283.22	-1.10

Red	2450.00	2.57	240.42	-1.36

Blue	2500.00	1.92	237.27	-1.78

Purple	5150.00	2.37	78.67	-1.91

Green	5200.00	4.80	79.30	0.32

Light brown	5250.00	4.49	79.93	-0.01

Orange	5750.00	6.34	283.85	1.08

Aqua	5850.00	4.67	283.22	-0.46

E n d U s e r M a n u a l : R F E x p o s u r e S t a t e m e n t s

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The end user manual must include the following information in a prominent location:

"IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter."

34	Connect Wi-Wave Hardware Reference, Rev A 2/2008

Image 32

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Updates G i i n f o r m a t i o nRelated DocumentationContact information To contact Digi International by UseAbout the Module A t u r e sDigi Connect Wi- Wave module edge connector A t ’ s o n t h e m o d u l e ?Digi Connect Wi- Wave module edge connector Pinout Pin Type Wlan Mini Card SignalB p e r i p h e r a l c o n t r o l l e r 2 1 b / g m o d e s a n d c h a n n e l sChannel Allocations Channel Center frequency Frequency spread MHz MHz MHzL t a g e r e g u l a t o r s L t a g e m o n i t o r R e s e t g e n e r a t o rW e r Features A t ’ s o n t h e d e v e l o p m e n t b o a r dDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 Pin Type Signal No connect or Jtagtdi Vcc3.3Debug signal breakout header LEDs D sI t c h e s a n d r e s e t f u n c t i o n a l i t y Alternative methods to triggerInput power jack, J3 Input power supply W e r s u p p l yJtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Using the Antenna Necessary Conditions for IntegrationConnect Wi-Wave antenna configurations T e n n a Specification s 2 d B i D i p o l e DimensionsN e r a l i n f o r m a t i o n AttributesAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram T e n n a Specification s 5 d B i D i p o l e Attribute BandRadiation pattern H-Plane 2.0 and 5.0 GHz Color Freq MHz Peak dBi Angle o Avg dBiRadiation pattern E-plane 2.0 and 5.0 GHz V i r o n m e n t a l Specification s C h a n i c a l d i m e n s i o n sW e r r e q u i r e m e n t s E x p o s u r e s t a t e m e n tF e t y s t a t e m e n t s Parameter LimitsModule Dimensions Development Board dimensions Appendix BCertifications C P a r t 1 5 C l a s s BModifications FCC Declaration of Conformity International EMC Standards StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008