Digi 90000797_A manual Modifications FCC

Page 38

C E R T I F I C A T I O N S

FCC Part 15 Class B

device must accept any interference received, including interference that may cause undesired operation.

If the FCC ID is not visible when installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module FCC ID. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: MCQ-50M1380, IC: 1846A-50M1380.

Modifications (FCC 15.21)

Changes or modifications to this equipment not expressly approved by Digi may void the user’s authority to operate this equipment.

Industry Canada

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

40	Connect Wi-Wave Hardware Reference, Rev A 2/2008

Image 38

Contents Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Related UpdatesG i i n f o r m a t i o n DocumentationContact information To contact Digi International by UseAbout the Module A t u r e sDigi Connect Wi- Wave module edge connector A t ’ s o n t h e m o d u l e ?Digi Connect Wi- Wave module edge connector Pinout Pin Type Wlan Mini Card SignalChannel Allocations B p e r i p h e r a l c o n t r o l l e r2 1 b / g m o d e s a n d c h a n n e l s Channel Center frequency Frequency spread MHz MHz MHzL t a g e r e g u l a t o r s L t a g e m o n i t o r R e s e t g e n e r a t o rW e r Features A t ’ s o n t h e d e v e l o p m e n t b o a r dDevelopment board Unpopulated components Digi Connect Wi-Wave module connector, J52 Pin Type Signal No connect or Jtagtdi Vcc3.3Debug signal breakout header LEDs D sI t c h e s a n d r e s e t f u n c t i o n a l i t y Alternative methods to triggerInput power jack, J3 Input power supply W e r s u p p l yJtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Using the Antenna Necessary Conditions for IntegrationConnect Wi-Wave antenna configurations N e r a l i n f o r m a t i o n T e n n a Specification s 2 d B i D i p o l eDimensions AttributesAntenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram T e n n a Specification s 5 d B i D i p o l e Attribute BandRadiation pattern H-Plane 2.0 and 5.0 GHz Color Freq MHz Peak dBi Angle o Avg dBiRadiation pattern E-plane 2.0 and 5.0 GHz V i r o n m e n t a l Specification s C h a n i c a l d i m e n s i o n sF e t y s t a t e m e n t s W e r r e q u i r e m e n t sE x p o s u r e s t a t e m e n t Parameter LimitsModule Dimensions Development Board dimensions Appendix BCertifications C P a r t 1 5 C l a s s BModifications FCC Declaration of Conformity International EMC Standards StandardsIndex Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008