Vanguard VI33NRA Optional Remote Operation, Thermostat Control Operation, Ghrc Series Operation

Page 17

OPERATING FIREPLACE INSERT

Optional Remote Operation

17

OPERATING FIREPLACE INSERT

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 30). Follow instructions included with the remote control.

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control set- ting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burners will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

For wall thermostat operation, follow instruction supplied with thermostat accessory GWMT1. For wall switch operation fol- low instructions supplied with GWMS2.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions on pages 15 and 16.

1. After lighting, let pilot flame burn for about one minute.

Turn control knob to ON position. Adjust flame adjust-

ment knob anywhere between HI and LO. Slide the remote

selector switch to the REMOTE position (see Figure 34).

Note: The burners may light if hand-held remote ON but-

ton was on when remote selector switch was last turned

off. You can now turn the burners on and off with the hand-

held remote control unit.

IMPORTANT: Do not leave the remote selector switch in

the REMOTE position when the pilot is not lit. This will

drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the

hand-held remote control unit for up to 3 seconds to assure

proper operation.

In the AUTO mode, the thermostat in the hand-held re- mote unit controls the room temperature. To increase the room temperature, press the top arrow of the TEMP but- ton. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer.

IMPORTANT: This remote control has been specially en- gineered to take an air temperature sample every 5.5 min- utes in the auto mode. It will not respond immediately to the temperature setting being turned up or down.

IMPORTANT: The hand-held remote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3.To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit.

IMPORTANT: To turn the pilot off, manually turn the con- trol knob on the heater to the OFF position.

Flame Adjustment Knob

IH

 

P

 

 

F

IL

 

 

 

O

 

 

F

 

T

 

 

O

 

 

 

 

 

 

 

 

 

O

 

 

 

 

N

ON

 

 

 

 

LO

 

 

 

OFF

 

 

 

 

REMOTE

Control Knob in

Remote Selector Switch in Remote

On Position

Position (Optional Remote Control)

Figure 34 - Setting the Remote Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

 

Increases Room

Shows Temperature

Temperature in

AUTO Mode

Setting

 

GHRC Series Operation:

2a. Press the ON/OFF button to turn the burner on and off. When turning burner off, the pilot will remain lit.

GHRCTA Series Operation:

2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 35). The lights to the left of the button will show AUTO, ON, or OFF.

The Log Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected

Decreases Room

Temperature in

AUTO Mode

Turns Burner On or Off and Allows You to Choose the Auto Setting

In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit.

Figure 35 - Thermostat Hand-Held Remote Control Unit Selections (GHRCTA Series only)

For morevisit www..com

110150-01B

Image 17
Contents Unvented VENT-FREE GAS Fireplace Insert OWNER’S Operation and Installation ManualVI33NRA VI33PRA Remote Ready GAS Fireplace InsertSafety Information Table of ContentsProduct Identification Log Base AssemblyProduct Features Remote Control AccessoriesLocal Codes UnpackingDetermining FRESH-AIR Flow for Heater Location Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installing Surround KIT GS38 or GS43 InstallationBlower Accessory Check GAS TypeAttaching Left Installing HoodFireplace Insert Installation Into Masonry Fireplace Installation ClearancesInstalling GAS Piping to Fireplace Location Fireplace Insert Installation Into FRAMED-IN EnclosureMantel Clearances for Insert Installation Installation Items NeededPropane/LP Connecting Fireplace Insert to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Insert Gas Connections Installing LogsGhrcta Installing Remote Receiver UnitFor Your Safety Read Before Lighting Installing 9-VOLT BatteriesInstalling 9-Volt Battery Not Included in Receiver Operating Fireplace InsertTo Turn OFF GAS To Appliance Manual Lighting ProcedureShutting Off Heater Shutting Off Burners Only pilot stays litThermostat Control Operation Optional Remote OperationGhrc Series Operation Ghrcta Series OperationInspecting Burners Logs Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Observed Problem Possible Cause TroubleshootingMaintenance, Observed Problem Possible Cause Remedy Specifications Wiring DiagramsReplacement Parts Service HintsRemote Ready Model VI33NRA Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListRemote Ready Model VI33PRA 103877-01 Lighting Instruction Plate 100563-01 Fireplace Insert VI33NRA VI33PRA 101784-01 Magnet Catch 102307-01 Strike Plate WALL-MOUNT Thermostat Switch Receiver and HAND-HELD Remote Control KIT Ghrc SeriesWALL-MOUNT ON/OFF Switch GWMS2 Cleaning KIT CCKOwners Registration Form Tape 110150-01B Warranty Information