Enviro 828 DV.FS, 828 MH, 828 DV.INS Operating Instructions, For Your Safety Read Before Operating

Page 20

12. OPERATING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A)This appliance is equipped with a pilot that must be lit by hand by following these instructions exactly.

B)BEFORE LIGHTING smell all around the appliance area for

gas, and next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas suppliers instructions.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above.

2.Turn off all electrical power to the appliance.

3. Turn the gas control knob clockwise

to the

“off’ position.

 

4.Open door. Wait five (5) minutes to clear out any gas. Close door. If you smell gas including near the floor,

STOP! Follow “B” in the above safety information. If you don’t smell gas go to next step.

5.Find the pilot located to the right between the front and

rear burner.

6. Turn gas control knob counter-clockwise to “PILOT”.

7.Push the gas control knob in fully and hold. Immediately light the pilot by pushing the piezo spark ignitor. Keep knob depressed for about 30 seconds after pilot is lit.

Release knob. If pilot goes out, repeat steps 4 through 6.

WARNING The gas valve has an lockout device which will not allow the pilot burner to be re-lit until the thermocouple has cooled.

•If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

•If you cannot reach your gas supplier, call the fire department.

C)Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not attempt to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D)Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water

•

8.EUROSIT VALVE:

Turn gas control knob counter-clockwise to the “LO” position. Then turn knob to the desired setting.

9. NOVASIT VALVE:

Turn gas control knob counter-clockwise to

the “ON” position. Flip burner switch to “ON” then turn “HI / LO” knob to the desired setting.

10.Turn on all electrical power to the unit

NOTE: Check to be sure the pilot flame engulfs the thermocouple and that the burners light completely.

TO TURN OFF GAS TO APPLIANCE

1.Turn the gas control knob clockwise to “OFF” DO NOT FORCE

2.Turn off all electrical power to the appliance if service is to be performed.

3.NOVA SIT VALVE: Flip burner switch to off.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents N E R S M a N U a L What to do if YOU Smell GASGeneral Safety PrecautionsFor Your Safety Table of Contents Codes and ApprovalsDimensions and Clearances to Combustibles FreestandingZero Clearance BOX Assembly Zero Clearance kit must be flush with the finished wallDeciding Where to Locate Your Stove Assembly InstructionsInstallation Fireplace InsertFireplace Insert Back Rail Insert Adapter Box Vent Coupling Front RailInstalling Burner Control Assembly Installing the Glowing EmbersDoor Removed Installing the LOG Do not Place Embers on the Rear BurnerFAN Installation Optional FAN Electrical RequirementsOrifice SIZES, Pressures and Btus GAS Line Connection and TestingNever USE AN Open Flame for Leak Testing AIR Shutter Adjustment Venting Vent Termination ClearancesPlanning Your Installation Venting Terminals Cannot be Recessed Into a Wall or SidingNumber Description 908B Pipe Length, Black Number DescriptionHorizontal Installation FIG-13 FIG-14 Vertical Installation FIG-16 FIG-17FIG-21 FIG-22 Cathedral Ceiling Installation Fireplace Insert Installation923F Co-Linear Flex Connectors Parts 923GKMobile Home Fuel Conversion To convert from Propane to Natural Gas or vise-versaLPG #59 frontFor Your Safety Read Before Operating Operating InstructionsWhat to do if YOU Smell GAS Lighting InstructionsMaintenance and Technical Cleaning of GlassTo Replace Door and Glass Assembly For Cleaning the Inside of the FireboxTrouble Shooting Problem Possible Cause SolutionDescription Parts and AccessoriesService Parts available from your local Envirogas Dealer Warranty To a Maximum of Seven YearsTo the Dealer To the DistributorInstallation Data Sheet Mail Address envirofire@home.com

828 MH, 828 DV.FS, 828 DV.INS specifications

The Enviro 828 series, including the 828 DV.INS, 828 DV.FS, and 828 MH models, represents a breakthrough in environmental technology, catering to both residential and commercial needs. These innovative systems are designed for efficiency, sustainability, and advanced functionality, making them suitable for various applications.

One of the standout features of the Enviro 828 series is its dual variable input system (DV.INS and DV.FS), which allows users to customize their energy consumption based on real-time demands. This technology not only optimizes performance but also enhances energy efficiency, leading to significant cost savings on utility bills. The adaptive modulation feature intelligently adjusts the output based on workload, ensuring that the system operates only as needed.

Another hallmark of the Enviro 828 series is its commitment to eco-friendliness. Incorporating state-of-the-art filtration technology, these units minimize emissions and reduce carbon footprints. They are equipped with high-efficiency particulate air (HEPA) filters, which are designed to capture even the smallest airborne particles, making them ideal for environments where air quality is a priority.

The 828 MH model further distinguishes itself with its multi-zone capabilities, allowing for distinct heating and cooling settings across different areas of a building. This feature is particularly beneficial in larger homes or office spaces, where temperature preferences may vary significantly from one room to another. Users can enjoy personalized comfort while maintaining overall energy efficiency.

Moreover, the Enviro 828 series employs advanced connectivity options, including smart home integration. Users can monitor and control their systems remotely through mobile applications, enabling real-time adjustments and stats tracking. This connectivity feature not only enhances user convenience but also allows for predictive maintenance alerts, ensuring longevity and operational reliability.

In summary, the Enviro 828 DV.INS, 828 DV.FS, and 828 MH models offer a perfect blend of efficiency, customization, and environmental consciousness. With their innovative technologies, such as dual variable input systems, advanced filtration, multi-zone capabilities, and smart connectivity, these units stand out as top choices for those seeking sustainable solutions in heating and cooling systems. Investing in an Enviro 828 model empowers users to prioritize comfort, efficiency, and environmental stewardship.
Top Page Image Contents