Enviro 828 DV.FS, 828 MH Installing Burner Control Assembly, Installing the Glowing Embers

Page 8

5. INSTALLING BURNER CONTROL ASSEMBLY

Remove the controls from box, check for shipping damage. Remove burner tray from controls (one screw on each side between burners).

Open door. Remove grate rod by pulling up at each end. Remove the 2 screws behind the grate and one screw on each side of control opening in firebox.

Extend flex gas line and place through hole in center of pedestal (freestanding and inserts) or through hole in right or left firebox side (insert only). Lower the controls into place at the back while pulling the flex line through on other side. Lower front into place, the control knob may need to be pushed in to allow burner controls to fit.

Install the two side screws, then install the front screws through the grate into the firebox. Replace burner tray.

Install the grate rod and logset.

6. INSTALLATION OF LOG SET and EMBERS

a. INSTALLING THE GLOWING EMBERS

A bag of ceramic fiber embers is provided for use on the front burner ember tray.

CAUTION: Use only the type of ember material supplied with this appliance. Due to the irregular size of the ember material there may be more than required. Use only a single layer. Do not pile embers. The use of other foreign materials on the burners may create dangerous conditions.

If over time, through cleaning and servicing, these embers require replacement, contact your nearest ENVIROGAS dealer for replacement embers.

Gently remove the ember material from the plastic bag. Spreading these pieces evenly across the front of the ember tray. Place a single layer of embers on top of the front burner. Carefully avoid any clumping or large build- ups.

Do not pack down, leave embers loose.

DO NOT PLACE EMBERS ON THE REAR BURNER.

Upon the first light up, watch for ignition to all burner ports. If a long delay is noted:

a)First, wait for the appliance to cool down

b)Open the front door of the appliance.

c)Checks to Carefully reposition the embers making sure that burner ports are not plugged solid or blocked

CAUTION: NEVER OPERATE THIS APPLIANCE WITH THE

DOOR REMOVED

INSTALLING THE LOG

Carefully remove log from unit. Check to ensure there is no damage. It is very important to install this log in its proper position to insure safe optimum operating conditions.

1.Open the front door.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents N E R S M a N U a L What to do if YOU Smell GASGeneral Safety PrecautionsFor Your Safety Table of Contents Codes and ApprovalsDimensions and Clearances to Combustibles FreestandingZero Clearance BOX Assembly Zero Clearance kit must be flush with the finished wallDeciding Where to Locate Your Stove Assembly InstructionsInstallation Fireplace InsertFireplace Insert Back Rail Insert Adapter Box Vent Coupling Front RailInstalling Burner Control Assembly Installing the Glowing EmbersDoor Removed Installing the LOG Do not Place Embers on the Rear BurnerFAN Installation Optional FAN Electrical RequirementsOrifice SIZES, Pressures and Btus GAS Line Connection and TestingNever USE AN Open Flame for Leak Testing AIR Shutter Adjustment Venting Vent Termination ClearancesPlanning Your Installation Venting Terminals Cannot be Recessed Into a Wall or SidingNumber Description 908B Pipe Length, Black Number DescriptionHorizontal Installation FIG-13 FIG-14 Vertical Installation FIG-16 FIG-17FIG-21 FIG-22 Cathedral Ceiling Installation Fireplace Insert Installation923F Co-Linear Flex Connectors Parts 923GKMobile Home Fuel Conversion To convert from Propane to Natural Gas or vise-versaLPG #59 frontFor Your Safety Read Before Operating Operating InstructionsWhat to do if YOU Smell GAS Lighting InstructionsMaintenance and Technical Cleaning of GlassTo Replace Door and Glass Assembly For Cleaning the Inside of the FireboxTrouble Shooting Problem Possible Cause SolutionDescription Parts and AccessoriesService Parts available from your local Envirogas Dealer Warranty To a Maximum of Seven YearsTo the Dealer To the DistributorInstallation Data Sheet Mail Address envirofire@home.com

828 MH, 828 DV.FS, 828 DV.INS specifications

The Enviro 828 series, including the 828 DV.INS, 828 DV.FS, and 828 MH models, represents a breakthrough in environmental technology, catering to both residential and commercial needs. These innovative systems are designed for efficiency, sustainability, and advanced functionality, making them suitable for various applications.

One of the standout features of the Enviro 828 series is its dual variable input system (DV.INS and DV.FS), which allows users to customize their energy consumption based on real-time demands. This technology not only optimizes performance but also enhances energy efficiency, leading to significant cost savings on utility bills. The adaptive modulation feature intelligently adjusts the output based on workload, ensuring that the system operates only as needed.

Another hallmark of the Enviro 828 series is its commitment to eco-friendliness. Incorporating state-of-the-art filtration technology, these units minimize emissions and reduce carbon footprints. They are equipped with high-efficiency particulate air (HEPA) filters, which are designed to capture even the smallest airborne particles, making them ideal for environments where air quality is a priority.

The 828 MH model further distinguishes itself with its multi-zone capabilities, allowing for distinct heating and cooling settings across different areas of a building. This feature is particularly beneficial in larger homes or office spaces, where temperature preferences may vary significantly from one room to another. Users can enjoy personalized comfort while maintaining overall energy efficiency.

Moreover, the Enviro 828 series employs advanced connectivity options, including smart home integration. Users can monitor and control their systems remotely through mobile applications, enabling real-time adjustments and stats tracking. This connectivity feature not only enhances user convenience but also allows for predictive maintenance alerts, ensuring longevity and operational reliability.

In summary, the Enviro 828 DV.INS, 828 DV.FS, and 828 MH models offer a perfect blend of efficiency, customization, and environmental consciousness. With their innovative technologies, such as dual variable input systems, advanced filtration, multi-zone capabilities, and smart connectivity, these units stand out as top choices for those seeking sustainable solutions in heating and cooling systems. Investing in an Enviro 828 model empowers users to prioritize comfort, efficiency, and environmental stewardship.
Top Page Image Contents