Enviro 828 DV.INS, 828 MH, 828 DV.FS owner manual Trouble Shooting, Problem Possible Cause Solution

Page 22

14. TROUBLE SHOOTING

 

Problem

Possible Cause

Solution

 

Spark will not light the pilot after

Defective piezo ignitor

Check connections to ignitor

 

repeated pressing of spark ignitor

 

-If ignitor connections are good but there is

 

 

 

no spark-replace ignitor

 

 

Broken spark electrode

-Check for broken ceramic insulation

 

 

 

replace, electrode if broken

 

 

Mis-aligned spark electrode

-If spark is not arcing from the electrode to

 

 

 

pilot- adjust by loosening screws on pilot

 

 

 

base. Adjust and re-tighten

 

Pilot will not remain lit

Problem with thermocouple circuit

-Check for proper connection of

 

 

 

thermocouple to rear of valve. If loose,

 

 

 

tighten lightly

 

 

 

-Check pilot for full flame impingement

 

 

 

around thermocouple. If the pilot is to small

 

 

 

- Check gas pressure, adjust pilot rate

 

 

 

screw, check pilot head for blockage.

 

 

 

-Check thermocouple voltage at valve- must

 

 

 

be greater than 5 mV. If low , replace

 

 

 

thermocouple.

 

 

Air in gas line - (Pilot flame dies while

-Bleed line.

 

 

knob is depressed.)

-Check gas line pressure.

 

 

 

-Contact dealer.

 

Burners will not remain lit

Problem with thermopile circuit

-Check gasline pressure.

 

 

(NOVASIT valve)

-Check for flame impingement on

 

 

 

thermopile, if low see “Pilot will not stay lit”

 

 

 

-check thermopile for a Minimum of 300 mV

 

 

 

when burner switched on.

 

 

 

-Check wiring to thermostat for breaks.

 

Flame lifting

Leak in vent pipe

-check for leaks in vent connections

 

 

Improper vent configuration

-check vent configuration with manual

 

 

Terminal may be recirculating flue

-check to see if terminal is on correctly

 

 

gases

-May need to install high wind termination

 

 

 

cap

 

 

 

-contact dealer.

 

Glass fogs up

Normal conditions - after the appliance warms up glass will clear

 

 

** Due to additives in gas, glass may get hazy during normal use**

 

 

Clean when needed.

 

 

Blue flames

Normal during start - flame will yellow as the appliance heats up.

 

 

 

 

 

Flames are burning “dirty” or

Flame impingement

-check log position

 

Sooting

 

-increase primary air by opening venturi

 

 

 

shutters

 

 

 

see also “Burners will not stay lit”

 

Flame goes out / comes on

Improper placement of thermostatic

move bulb to cooler location

 

frequently during a short period of

bulb

 

 

time

 

 

 

 

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents N E R S M a N U a L What to do if YOU Smell GASFor Your Safety Safety PrecautionsGeneral Table of Contents Codes and ApprovalsDimensions and Clearances to Combustibles FreestandingZero Clearance BOX Assembly Zero Clearance kit must be flush with the finished wallInstallation Deciding Where to Locate Your StoveAssembly Instructions Fireplace InsertFireplace Insert Back Rail Insert Adapter Box Vent Coupling Front RailDoor Removed Installing the LOG Installing Burner Control AssemblyInstalling the Glowing Embers Do not Place Embers on the Rear BurnerFAN Installation Optional FAN Electrical RequirementsNever USE AN Open Flame for Leak Testing GAS Line Connection and TestingOrifice SIZES, Pressures and Btus AIR Shutter Adjustment Venting Vent Termination ClearancesNumber Description 908B Pipe Length, Black Planning Your InstallationVenting Terminals Cannot be Recessed Into a Wall or Siding Number DescriptionHorizontal Installation FIG-13 FIG-14 Vertical Installation FIG-16 FIG-17FIG-21 FIG-22 923F Co-Linear Flex Connectors Cathedral Ceiling InstallationFireplace Insert Installation Parts 923GKLPG Mobile Home Fuel ConversionTo convert from Propane to Natural Gas or vise-versa #59 frontWhat to do if YOU Smell GAS For Your Safety Read Before OperatingOperating Instructions Lighting InstructionsTo Replace Door and Glass Assembly Maintenance and TechnicalCleaning of Glass For Cleaning the Inside of the FireboxTrouble Shooting Problem Possible Cause SolutionService Parts available from your local Envirogas Dealer Parts and AccessoriesDescription To the Dealer WarrantyTo a Maximum of Seven Years To the DistributorInstallation Data Sheet Mail Address envirofire@home.com

828 MH, 828 DV.FS, 828 DV.INS specifications

The Enviro 828 series, including the 828 DV.INS, 828 DV.FS, and 828 MH models, represents a breakthrough in environmental technology, catering to both residential and commercial needs. These innovative systems are designed for efficiency, sustainability, and advanced functionality, making them suitable for various applications.

One of the standout features of the Enviro 828 series is its dual variable input system (DV.INS and DV.FS), which allows users to customize their energy consumption based on real-time demands. This technology not only optimizes performance but also enhances energy efficiency, leading to significant cost savings on utility bills. The adaptive modulation feature intelligently adjusts the output based on workload, ensuring that the system operates only as needed.

Another hallmark of the Enviro 828 series is its commitment to eco-friendliness. Incorporating state-of-the-art filtration technology, these units minimize emissions and reduce carbon footprints. They are equipped with high-efficiency particulate air (HEPA) filters, which are designed to capture even the smallest airborne particles, making them ideal for environments where air quality is a priority.

The 828 MH model further distinguishes itself with its multi-zone capabilities, allowing for distinct heating and cooling settings across different areas of a building. This feature is particularly beneficial in larger homes or office spaces, where temperature preferences may vary significantly from one room to another. Users can enjoy personalized comfort while maintaining overall energy efficiency.

Moreover, the Enviro 828 series employs advanced connectivity options, including smart home integration. Users can monitor and control their systems remotely through mobile applications, enabling real-time adjustments and stats tracking. This connectivity feature not only enhances user convenience but also allows for predictive maintenance alerts, ensuring longevity and operational reliability.

In summary, the Enviro 828 DV.INS, 828 DV.FS, and 828 MH models offer a perfect blend of efficiency, customization, and environmental consciousness. With their innovative technologies, such as dual variable input systems, advanced filtration, multi-zone capabilities, and smart connectivity, these units stand out as top choices for those seeking sustainable solutions in heating and cooling systems. Investing in an Enviro 828 model empowers users to prioritize comfort, efficiency, and environmental stewardship.
Top Page Image Contents