Princess PI 1010A manual Tools Needed for Installation, Stove Assembly, Product Inspection

Page 17

Preparation And Assembly

Princess PI1010A INSERT STOVE INSTALLATION PROCEDURE

AFTER YOU READ AND FULLY UNDERSTAND THE MATERIAL IN THIS MANUAL, YOU ARE READY TO PROCEED WITH THE INSTALLATION OF YOUR STOVE.

Before beginning the installation, thoroughly clean and inspect the fireplace and chimney you are using. Professional assistance is recommended, your local certified installer should be contacted to provide installation and inspection services.

TOOLS NEEDED FOR INSTALLATION

If you are planning to install this stove yourself, you will need the tools listed below. Consult the chimney and flue connector manufacturer's installation instructions for tools needed for chimney installation.

-1/4" Wrench, Nut driver, or Socket with Handle.

-Medium Flat Blade Screwdriver, Phillips Screwdriver and #2 Square Drive Screwdriver

-Tape Measure.

-Carpenter's Level.

See OPTIONS section for tools needed.

STOVE ASSEMBLY

Remove all items packed in the firebox.

IF YOU HAVE NOT ALREADY DONE SO, PLEASE TAKE A FEW MINUTES TO COMPLETE THE WAR- RANTY CARD FOUND IN THE FIREBOX AND MAIL IT TODAY.

PRODUCT INSPECTION

BLAZE KING Stoves are known for their quality materials and construction. However, mistakes occasionally oc- cur. Inspect all parts for damage due to shipping and to be sure that all needed parts are enclosed. If you dis- cover a part is missing or damaged, contact your dealer immediately for replacement or repair. Refer to the part number listed on page 32 and the model and serial numbers of your stove (see the tag on the back of the stove).

COMBUSTOR ASSEMBLY, INSTALLATION

See page 26 for proper parts names. This stove is generally shipped from the factory with the combustor in- stalled. If the combustor is not installed, follow the instructions on page 27 under Catalytic Combustor, Replace- ment, beginning with Step 6.

FLAME SHIELD, INSTALLATION

The flame shield is a stainless steel plate, punched with many 3/8” holes. If the flame shield has fallen off during shipping then it must be installed before the first fire. Hold it in the firebox with the triangular wings facing away. Lift it between the loading door and the catalyst, and rest the bottom of the plate on the two pins that protrude below the catalyst. The flame shield should rest at an angle (about 45 degrees) with its bottom near the combus- tor, and its top near the stove front.

OPTIONAL ACCESSORIES

Gold Door—Part# Z4686G-C

REPLACEMENT PARTS

See page 32.

BEFORE YOU PUT YOUR STOVE IN PLACE, YOU

MUST ATTACH THE WARNING PLATE THAT WAS

INCLUDED WITH YOUR STOVE (SHOWN TO THE

RIGHT). THIS LABEL PLATE MUST BE

ATTACHED TO THE INSIDE WALL OF YOUR

FIREPLACE.

PI-1010A

Page 17

DATE PRINTED: 2/8/05

Revision Date: 02/01/05

Image 17
Contents Princess Insert Princess Insert Approval LabelTo Our Valued Customers Blaze KingChimneys Masonry Fireplace Safety NoticeTable Of Contents Operation HOW YOU can GET Service WarrantyDefinitions Creosote Formation and Need for Removal Combustion AIR IntakeDOOR, Loading DraftFuel This Stove is for USE with Solid Wood Fuel only FlueHearth ICE Formation and PreventionSafety Children CleaningChimneys Clearances to Combustible MaterialsFuel Electrical PowerDisposal of Ashes Loading DoorBtu Ratings PI1010A SpecificationsFacts On BTU’s Planning for Your Stove Placement Preparation And AssemblyInspect Your Chimney Chimney Height Affects Draft22 559 mm Stove Assembly Tools Needed for InstallationCombustor ASSEMBLY, Installation Flame SHIELD, InstallationAssembly Instructions for Princess PI1010A Insert Assembly GeneralScrew Installation Into Factory Built Fireplaces Chimneys FACTORY-BUILT Fireplace Installation ChimneyChimney Installation General Fuel OperationFAN Operation Your First FireCouple of tips Maintenance Catalytic COMBUSTOR, Testing Gasket ReplacementCatalytic COMBUSTOR, Cleaning Gasket InspectionDoor GLASS, Replacement Catalytic COMBUSTOR, ReplacementDoor GLASS, Cleaning Paint FAN AssemblyRheostat Replacement Problem TroubleshootingCause Solution Chimney FireCause PROBLEM. Too much heatHazard and demands immediate attention Problem Door glass quickly becomes coated with creosoteStandard & Replacements Parts Standard And Replacement PartsPart Name Optional KitsDate Printed 2/8/05