Desa (V)TC36N SERIES, (V)TC36P SERIES REMOVING/REPLACING Glass Door, Installing Remote Receiver

Page 21

FIREPLACE INSTALLATION

Installing Optional Wireless Hand-Held Remote Control - GHRCB and GHRCTB Series Removing/Replacing Glass Door

21

FIREPLACE INSTALLATION

Continued

INSTALLING OPTIONAL WIRELESS HAND- HELD REMOTE CONTROL - GHRCB AND GHRCTB SERIES

NOTICE: Use only alkaline batteries (not included).

Installing Remote Receiver

1.Open bottom louver and locate the switch bracket on the right.

2.Unscrew the switch bracket. Lean bracket forward so you are able to access the back of the remote receiver.

3.Locate the battery clip mounted on the back of the receiver. Slide a 9-volt alkaline battery (not included) through the clip (see Figure 37).

4.Attach the terminal wires to the battery.

5.Connect wires from receiver to TH and TPTH to control valve (see Figure 38).

6.Replace the switch bracket.

Receiver

9-Volt Alkaline

Battery

Terminal Wires

Battery Clip

Figure 37 - Attaching Alkaline Battery to Receiver

To Optional

Remote

Accessory

Figure 38 - Control Valve Terminals

Installing 9-Volt Alkaline Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to a 9-volt alkaline battery (not included). Place battery into the battery housing.

3.Replace battery cover onto remote control unit.

Battery Cover

Remote Control Unit

Terminal

 

Wires

 

9-Volt

 

Alkaline

Battery

Battery

Housing

 

Figure 39 - Installing Alkaline Battery in Hand-Held Remote

Control Unit (GHRCB)

 

9-Volt

Terminal

Wires

Battery

Remote

 

 

Control

 

Unit

 

Battery

 

Cover

Figure 40 - Installing Battery in Hand-Held Remote Control Unit

(GHRCTB Series)

 

REMOVING/REPLACING GLASS DOOR

CAUTION: Do not operate this fireplace with a

broken glass door panel or without the glass door

panel securely in place. For replacement part infor-

mation see Replacement Parts, page 31.

CAUTION: Wear gloves and safety glasses while

handling or removing broken glass. Do not remove if

glass is hot. Keep children and pets away from glass.

WARNING: If fireplace has been running, turn

off and unplug fireplace. Let cool before removing

glass door or louvers.

 

Removing Louver Panels

Remove the top and bottom louver panels by simultaneously pulling

both top end spring latches towards the center of the appliance until

they are disengaged from the locating holes (see Figure 41). Repeat

for bottom spring latches and pull the louvers outward. To install or

replace items removed, simply reverse the procedures above.

Louver Panel

Spring Latch

Figure 41 - Removing Louver Panel

116192-01B

www.desatech.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For Your Safety For Your Safety What to do if YOU Smell GASSave this manual for future reference Safety Information Table of ContentsLocal Codes Safety Information Product IdentificationProduct Features PRE-INSTALLATION PreparationLocation and Space Requirements Framing and Finishing ClearancesTermination CAP AIR Supply Inlet GAS Meter Location of Termination CAPInstallation Precautions Venting Installation InstructionsHorizontal Termination Installation Installation PlanningInstalling Siding Standoff Combustible Vertical Horizontal H Horizontal Termination ConfigurationsCorner Installation Vertical Horizontal H Horizontal H 1 + Venting with Two 90 ElbowsMin Max 12 max 18 max 20 max Vertical Horizontal H 1 + Min Max 12 max 18 max 20 maxInstallation for Vertical Termination Flat Ceiling InstallationConnect a section of pipe and extend up through the hole Vertical Horizontal H 1 + Min Max 20 max Vertical Termination ConfigurationsVenting with One 90 Elbow Vertical Horizontal H Min Max 20 maxHigh Altitude Installation Vertical Venting= 40 max Fireplace Installation Venting InstallationInstalling Optional Blower Accessories Check GAS TypeBy turning knob fully counterclockwise before continuing Model BKT InstallationDecal on the firebox bottom approximately 12 in front Blower see FigureBlower Wiring Diagram Installing GAS Piping to Fireplace LocationInstallation Items Needed Blower see ,Connecting Fireplace to GAS Supply Checking GAS ConnectionsOr servicing. Correct all leaks at once Pressure Testing Fireplace Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Remote Receiver REMOVING/REPLACING Glass DoorRemoving Louver Panels Installing Lava Rock and Glowing Embers Cleaning Glass DoorRemoving Glass Doors For Your Safety Read Before Lighting Installing Brick Liner Models BL36DASA and BL36DHASAOperating Fireplace Lighting InstructionsTo Turn OFF GAS Manual Lighting ProcedureOptional HAND-HELD Remote Operation Shutting Off Burners Only pilot stays litManual Mode Safety FeaturesAuto Thermostatic Mode ON/OFF Series Model GhrcbPilot Assembly Operating Optional Blower AccessoryInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning and MaintenancePilot and Burners LogsTroubleshooting Inlet gas pressure is too low Is low Remote controlCompany Thermopile leads disconnected or imAbove Gas leak. See Warning statementService Hints Replacement PartsTechnical Service SpecificationsModels TC36N, VTC36N, TC36P and VTC36P Illustrated Parts BreakdownKEY Part Number TC36N/P VTC36N/P Description QTY Parts ListBurner Assembly for Models TC36N, VTC36N, TC36P and VTC36P KEY Part Number Description QTY Accessories Owners Registration Form Industrial Drive Box Bowling Green, KY 116192-01B Industrial Drive P.O. Box Model Serial No Date Purchased
Top Page Image Contents