Desa (V)TC36P SERIES Vertical Termination Conﬁgurations, Vertical Horizontal H 1 + Min Max 20 max

Page 14

14

VENTING INSTALLATION INSTRUCTIONS

Installation for Vertical Termination (Cont.)

VENTING INSTALLATION INSTRUCTIONS

Continued

Vertical Termination Conﬁgurations

Figures 21 through 24 show four different conﬁgurations for verti- cal termination.

Venting with Two 90° Elbows

Vertical (V)	Horizontal (H1) +
	Horizontal (H2)
5' min.	2' max.
6' min.	4' max.
7' min.	6' max.
8' min.	8' max.
20' max.	8' max.

45° Elbow	Note: Install
45° Elbow	restrictor into inner
	collar of ﬁreplace
	as shown.

Venting with One 90° Elbow

	Vertical (V)	Horizontal (H)
	5' min.	2' max.
	6' min.	4' max.
	7' min.	6' max.
	8' min.	8' max.
	20' max.	8' max.
	45° Elbow	Note: Install
	45° Elbow	restrictor into inner
		restrictor into inner
		collar of ﬁreplace
		as shown.

Figure 22 - Vertical Venting Conﬁguration Using One 90° Elbow (Vertical Round High Wind Termination Shown)

Figure 21 - Vertical Venting Conﬁguration Using Two 90° Elbows with Two Horizontal Runs (Vertical Round High Wind Termination Shown)

Venting with Two 90° Elbows

Vertical (V1)	Horizontal (H)
5' min.	6' max.
6' min.	12' max.
7' min.	18' max.
8' min.	20' max.

Note: Install restrictor into inner collar of ﬁreplace as shown.

45° Elbow

Note: Vertical (V1) + Vertical (V2) = 40' max.

Figure 23 - Vertical Venting Conﬁguration Using Two 90° Elbows (Vertical Round High Wind Termination Shown)

www.desatech.com

116192-01B

Image 14

Contents Save this manual for future reference For Your SafetyFor Your Safety What to do if YOU Smell GAS Table of Contents Safety InformationSafety Information Product Identification Local CodesLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Clearances Framing and FinishingLocation of Termination CAP Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Siding Standoff Combustible Horizontal Termination Conﬁgurations Vertical Horizontal HCorner Installation Min Max 12 max 18 max 20 max Venting with Two 90 ElbowsVertical Horizontal H Horizontal H 1 + Vertical Horizontal H 1 + Min Max 12 max 18 max 20 maxConnect a section of pipe and extend up through the hole Installation for Vertical TerminationFlat Ceiling Installation Venting with One 90 Elbow Vertical Termination ConﬁgurationsVertical Horizontal H 1 + Min Max 20 max Vertical Horizontal H Min Max 20 max= 40 max High Altitude InstallationVertical Venting Installing Optional Blower Accessories Venting InstallationFireplace Installation Check GAS TypeDecal on the ﬁrebox bottom approximately 12 in front Model BKT InstallationBy turning knob fully counterclockwise before continuing Blower see FigureInstallation Items Needed Installing GAS Piping to Fireplace LocationBlower Wiring Diagram Blower see ,Or servicing. Correct all leaks at once Connecting Fireplace to GAS SupplyChecking GAS Connections Installing Optional Wall Mount Switch GWMS2 Pressure Testing Fireplace Gas ConnectionsRemoving Louver Panels Installing Remote ReceiverREMOVING/REPLACING Glass Door Removing Glass Doors Installing Lava Rock and Glowing EmbersCleaning Glass Door Operating Fireplace Installing Brick Liner Models BL36DASA and BL36DHASAFor Your Safety Read Before Lighting Lighting InstructionsOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS Shutting Off Burners Only pilot stays litAuto Thermostatic Mode Safety FeaturesManual Mode ON/OFF Series Model GhrcbInspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning and MaintenanceGlass Door LogsTroubleshooting Company Is low Remote controlInlet gas pressure is too low Thermopile leads disconnected or imGas leak. See Warning statement AboveTechnical Service Replacement PartsService Hints SpecificationsIllustrated Parts Breakdown Models TC36N, VTC36N, TC36P and VTC36PParts List KEY Part Number TC36N/P VTC36N/P Description QTYBurner Assembly for Models TC36N, VTC36N, TC36P and VTC36P KEY Part Number Description QTY Accessories Owners Registration Form Industrial Drive Box Bowling Green, KY 116192-01B Model Serial No Date Purchased Industrial Drive P.O. Box