Desa (V)V36EN installation manual Connecting Fireplace to GAS Supply, Checking GAS Connections

Page 20

20

FIREPLACE INSTALLATION

Connecting Fireplace To Gas Supply Checking Gas Connections

FIREPLACE INSTALLATION

Continued

CONNECTING FIREPLACE TO GAS SUPPLY

Installation Items Needed

5/16" hex socket wrench or nut-driver

sealant (resistant to propane/LP gas, not provided)

1.Open lower louver door panel by gently pulling forward.

2.Route flexible gas line (provided by installer) from equipment shutoff valve to fireplace. Route flexible gas supply line through one of the access holes on side of fireplace.

3.Attach flexible gas line from gas supply to control valve (see Figure 32).

4.Check all gas connections for leaks. See Checking Gas Connections.

 

Red Surface Indicates

Equipment

For Propane/LP Use Only

Flexible Gas Line

Shutoff Valve

Do NOT Kink

1/2" NPT Incoming

 

 

Gas Line

Inlet Pressure Tap

Outlet Pressure Tap

 

Note: Wire Connections Not Shown for Clarity

Figure 32 - Connecting Flexible Gas Line to Electronic Valve

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

4.Check all joints of gas supply piping system. Apply noncorro- sive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

5.Reconnect fireplace and equipment shutoff valve to gas sup- ply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1.Close equipment shutoff valve (see Figure 33).

2.Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas fireplace or opening main gas valve located on or near gas meter for natural gas fire- place, or using compressed air.

3.Check all joints from propane/LP supply tank or gas meter to equipment shutoff valve (see Figure 34 for propane/LP or Figure 35 for natural gas). Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

Equipment

Open

Shutoff

 

Valve

 

 

Closed

Figure 33 - Equipment Shutoff Valve

 

Equipment

Propane/LP

Shutoff

Valve

Supply Tank

 

 

Gas Valve

Figure 34 - Checking Gas Joints for Propane/LP Gas Fireplace

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1.Disconnect fireplace and its individual equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig (3.5 kPa) will damage fireplace gas regulator.

2.Cap off open end of gas pipe where equipment shutoff valve was connected.

3.Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas fireplace or opening main gas valve located on or near gas meter for natural gas fire- place, or using compressed air.

Equipment

Shutoff

Valve

Gas

Meter

Gas Valve

Figure 35 - Checking Gas Joints for Natural Gas Fireplace

For..com

108862

Image 20
Contents For Your Safety What to do if YOU Smell GAS TM OWNER’S Operation Installation ManualFor Your Safety Table of Contents Safety InformationLocal Codes Product IdentificationLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Clearances Framing and FinishingLocation of Termination CAP Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Horizontal Vent Cap V36 Series 35 min 17 max V42 Series 39 min Horizontal Termination ConfigurationsHorizontal H Corner Installation Horizontal System Installation Using TWO 90 Elbows Venting with Two 90 ElbowsInstallation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations Venting with One 90 ElbowHigh Altitude Installation Vertical VentingFireplace Installation Parts Lists for Venting Kits and ComponentsInstalling Optional Blower Accessory Check GAS TypeAttaching Speed Control to Firebox Model BKT Installation Blower Wiring DiagramInstalling GAS Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Fireplace Gas Connections Cleaning Glass DoorREMOVING/REPLACING Glass Door Removing Louver PanelsInstalling LOGS, Lava Rock and Glowing Embers Installing Left Side and Top Brick PanelsInstalling Log No Optional Remote Control Wiring DiagramWall Switch Installation For Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS To ApplianceOperating Optional Blower Accessory Pilot AssemblyInspecting Burners Burner Flame PatternCleaning Maintenance Glass DoorPilot and Burners LogsTroubleshooting Observed Problem Possible Cause RemedyGas leak. See Warning statement at TopReplacement Parts Service Hints SpecificationsTechnical Service Parts Under WarrantyAccessories Illustrated Parts Breakdown Parts List VV36EPS VV36EPH Description QTYBurner Assembly for Models KEY Part Number Description QTY VV42EN, VV42ENS, VV42ENH VV42EP, VV42EPS, VV42EPH VV42ENS VV42ENH Illustrated Parts Breakdown KEY Part Number Description QTY Warranty Information

(V)V36EN specifications

Desa (V)V36EN is a cutting-edge technological solution that combines advanced features and innovative capabilities to enhance user experience and operational efficiency. This state-of-the-art product is designed to cater to a wide range of applications, making it an essential tool across various industries.

One of the standout features of the Desa (V)V36EN is its robust and flexible architecture. This design allows for seamless integration with existing systems, minimizing downtime during implementation and maximizing productivity from the get-go. The system is engineered to support various communication protocols, ensuring compatibility with numerous devices and platforms. This versatility makes it a valuable asset for businesses looking to streamline processes and improve connectivity.

In terms of performance, the Desa (V)V36EN boasts impressive processing capabilities. It utilizes high-speed processors that enable rapid data analysis and decision-making, thereby optimizing workflows. Additionally, featuring advanced data management technologies, the system can handle large volumes of data efficiently. This ensures that users can access critical information in real-time, empowering them to make informed decisions quickly.

Security is another paramount feature of the Desa (V)V36EN. With built-in security protocols and encryption technologies, the system safeguards sensitive information against unauthorized access and cyber threats. This focus on security not only protects business data but also enhances user trust, making it a reliable choice for organizations across various sectors.

User-friendliness is a key characteristic of the Desa (V)V36EN. The intuitive interface ensures that users can navigate the system with ease, requiring minimal training to operate effectively. This aspect significantly reduces the learning curve, allowing teams to adopt the technology rapidly and start reaping the benefits.

Finally, the Desa (V)V36EN is designed with scalability in mind. As businesses grow and evolve, the system can be easily updated and expanded to accommodate increasing demands. Whether it’s integrating new features or scaling up operational capabilities, this flexibility makes it a long-term solution for organizations seeking innovation.

In conclusion, the Desa (V)V36EN stands out as a comprehensive technological solution that combines flexibility, performance, security, user-friendliness, and scalability. It is an ideal choice for organizations looking to improve efficiency, enhance productivity, and stay ahead in a competitive landscape.