Desa (V)V36EN Inspecting Burners, Operating Optional Blower Accessory, Pilot Assembly

Page 26

26

OPERATING FIREPLACE

Operating Optional Blower Accessory

INSPECTING BURNERS

Pilot Assembly

Burner Flame Pattern

OPERATING FIREPLACE

Continued

OPERATING OPTIONAL

BLOWER ACCESSORY

Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.

The BK manual blower and the BKT thermostatically-con- trolled blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

Note for BKT Only: If you are using BKT blower with optional thermostat (wall mounted or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.

The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.

INSPECTING BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame. Alterations may have occurred during shipping and handling. The pilot is located on the back right hand side of the burner.

The flame must envelope 1/4" of top of the ignitor/sensor and grounding stem.

If your pilot assembly does not meet these requirements:

•Turn the adjustment screw marked PILOT clockwise to decrease or counterclockwise to increase the flame to proper size (see Figure 49, page 25). Do not remove the adjustment screw.

•see Troubleshooting, pages 28 and 29

Pilot Burner

Sensing Rod

 

 

Ignitor/Sensor

Figure 51 - Correct Pilot Flame Pattern

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incorrectly, the flames will lift or "ghost". This can be dangerous. Inspect the flames after installa- tion to ensure proper installation and performance.

Figure 52 shows a typical flame pattern for (V)V36E and (V)V42E series models.

If burner flame pattern differs from that described:

•turn fireplace off (see To Turn Off Gas to Appliance, page 25)

•see Troubleshooting, pages 28 and 29

Figure 52 - Typical Flame Pattern for (V)V36E and (V)V42E Series

Models

For..com

108862

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Your Safety What to do if YOU Smell GAS TM OWNER’S Operation Installation ManualFor Your Safety Table of Contents Safety InformationLocal Codes Product IdentificationLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Clearances Framing and FinishingLocation of Termination CAP Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Horizontal Vent Cap V36 Series 35 min 17 max V42 Series 39 min Horizontal Termination ConfigurationsHorizontal H Corner Installation Horizontal System Installation Using TWO 90 Elbows Venting with Two 90 ElbowsInstallation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations Venting with One 90 ElbowHigh Altitude Installation Vertical VentingInstalling Optional Blower Accessory Fireplace InstallationParts Lists for Venting Kits and Components Check GAS TypeAttaching Speed Control to Firebox Model BKT Installation Blower Wiring DiagramInstalling GAS Piping to Fireplace Location Installation Items NeededPressure Testing Gas Supply Piping System Connecting Fireplace to GAS SupplyInstallation Items Needed Checking GAS ConnectionsREMOVING/REPLACING Glass Door Pressure Testing Fireplace Gas ConnectionsCleaning Glass Door Removing Louver PanelsInstalling LOGS, Lava Rock and Glowing Embers Installing Left Side and Top Brick PanelsInstalling Log No Optional Remote Control Wiring DiagramWall Switch Installation Lighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To ApplianceInspecting Burners Operating Optional Blower AccessoryPilot Assembly Burner Flame PatternPilot and Burners Cleaning MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible Cause RemedyGas leak. See Warning statement at TopTechnical Service Replacement Parts Service HintsSpecifications Parts Under WarrantyAccessories Illustrated Parts Breakdown Parts List VV36EPS VV36EPH Description QTYBurner Assembly for Models KEY Part Number Description QTY VV42EN, VV42ENS, VV42ENH VV42EP, VV42EPS, VV42EPH VV42ENS VV42ENH Illustrated Parts Breakdown KEY Part Number Description QTY Warranty Information

(V)V36EN specifications

Desa (V)V36EN is a cutting-edge technological solution that combines advanced features and innovative capabilities to enhance user experience and operational efficiency. This state-of-the-art product is designed to cater to a wide range of applications, making it an essential tool across various industries.

One of the standout features of the Desa (V)V36EN is its robust and flexible architecture. This design allows for seamless integration with existing systems, minimizing downtime during implementation and maximizing productivity from the get-go. The system is engineered to support various communication protocols, ensuring compatibility with numerous devices and platforms. This versatility makes it a valuable asset for businesses looking to streamline processes and improve connectivity.

In terms of performance, the Desa (V)V36EN boasts impressive processing capabilities. It utilizes high-speed processors that enable rapid data analysis and decision-making, thereby optimizing workflows. Additionally, featuring advanced data management technologies, the system can handle large volumes of data efficiently. This ensures that users can access critical information in real-time, empowering them to make informed decisions quickly.

Security is another paramount feature of the Desa (V)V36EN. With built-in security protocols and encryption technologies, the system safeguards sensitive information against unauthorized access and cyber threats. This focus on security not only protects business data but also enhances user trust, making it a reliable choice for organizations across various sectors.

User-friendliness is a key characteristic of the Desa (V)V36EN. The intuitive interface ensures that users can navigate the system with ease, requiring minimal training to operate effectively. This aspect significantly reduces the learning curve, allowing teams to adopt the technology rapidly and start reaping the benefits.

Finally, the Desa (V)V36EN is designed with scalability in mind. As businesses grow and evolve, the system can be easily updated and expanded to accommodate increasing demands. Whether it’s integrating new features or scaling up operational capabilities, this flexibility makes it a long-term solution for organizations seeking innovation.

In conclusion, the Desa (V)V36EN stands out as a comprehensive technological solution that combines flexibility, performance, security, user-friendliness, and scalability. It is an ideal choice for organizations looking to improve efficiency, enhance productivity, and stay ahead in a competitive landscape.
Top Page Image Contents