Desa (V)V36EN Product Features, PRE-INSTALLATION Preparation, Location and Space Requirements

Page 4

4

PRODUCT FEATURES PRE-INSTALLATION PREPARATION

Location and Space Requirements

PRODUCT FEATURES

These are a few facts that can help you understand and enjoy your direct-vent fireplace:

•The venting system may be routed to the outside of your home in several ways. It may vent through the roof (vertical) or it may vent to an outside/exterior wall (horizontal). The vent pipe in- stallation is very important to allow for proper operation. You must follow the venting instructions very carefully for either vertical or horizontal applications.

•This fireplace may be installed in any room of your house provided all local codes and these installation instructions are followed.

•This fireplace does not require electricity to operate.

•Only the blower requires electricity if installed and if you plan to install the blower at a later date, do not forget to wire the outlet at the bottom of the fireplace when framing.

•A piezo ignitor and ceramic electrode create spark to ignite the pilot light. It does not require any matches, batteries or any other sources of ignition to light the pilot.

•Each time you turn on your fireplace, you may notice some amount of condensation on the inside of the fireplace glass. This is normal and will disappear after 10-20 minutes of operation.

•Your direct-vent gas fireplace system (fireplace and venting) is a balanced and sealed gas operating unit. It requires approximately 10-20 minutes of operating time before the flame pattern stabilizes.

PRE-INSTALLATION

PREPARATION

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efficient location for your DESA International direct-vent fireplace. Make sure that rafters and wall studs are not in the way of the venting system. Choose a location where the heat output is not affected by drafts, air conditioning ducts, windows or doors. Figure 2 shows some common locations. Be aware of all restrictions and precautions before deciding the exact location for your fireplace and termination cap.

When deciding the location of your fireplace, follow these rules:

•Do not connect this fireplace venting to a chimney flue serving a separate solid-fuel burning fireplace or appliance.

•Due to high temperatures, do not locate this fireplace in high traf- fic areas, windy or drafty areas, or near furniture or draperies.

•Proper clearances must be maintained.

•Your fireplace is designed to be used in zero clearance installa- tions. Wall or framing material can be placed directly against any exterior surface on the back, sides, or top of your fireplace, except where standoff spacers are integrally attached. If stand- off spacers are attached to your fireplace, these spacers can be placed directly against wall or framing material. See framing details on page 5.

•If you plan on installing a television or entertainment center re- cessed above your fireplace, it is recommended that you main- tain a minimum 18" above top of louver opening.

•When locating termination cap, it is important to observe the minimum clearances shown in Figure 7, page 6.

•If recessing into a wall, you can avoid extra framing by position- ing your fireplace against an already existing framing member.

•Do not recess termination cap into a wall or siding.

•You may paint the termination cap with 450ºF (232ºC) heat- resistant paint to coordinate with the exterior finish.

•There must not be any obstruction such as bushes, garden sheds, fences, decks, or utility buildings within 24" from the front of the termination cap.

•Do not locate termination cap where excessive snow or ice build up may occur. Be sure to clear vent termination area after snow falls to prevent accidental blockage of venting system. When using snow blowers, do not direct snow towards vent termina- tion area.

Flush with a wall

Through exterior wall enclosed in a chase

Corner installation

Figure 2 - Common Fireplace Locations

RW

D

•If your fireplace is to be installed directly on carpeting, vinyl tile, or any combustible material other than wood, it must be installed on a metal or wood panel extending the full width and depth of the fireplace. See Figure 3.

FW

Fireplace size

D x FW x RW

 

 

 

 

36"

21 1/8"

41"

29"

42"

23 1/4"

48"

35 7/8"

Figure 3 - Fireplace Bottom Dimensions

For..com

108862

Page 3 Page 5
Image 4
Page 3 Page 5
Contents For Your Safety TM OWNER’S Operation Installation ManualFor Your Safety What to do if YOU Smell GAS Table of Contents Safety InformationLocal Codes Product IdentificationPRE-INSTALLATION Preparation Product FeaturesLocation and Space Requirements Clearances Framing and FinishingLocation of Termination CAP Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Horizontal Vent Cap Horizontal H Horizontal Termination ConfigurationsV36 Series 35 min 17 max V42 Series 39 min Corner Installation Horizontal System Installation Using TWO 90 Elbows Venting with Two 90 ElbowsInstallation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations Venting with One 90 ElbowHigh Altitude Installation Vertical VentingFireplace Installation Parts Lists for Venting Kits and ComponentsInstalling Optional Blower Accessory Check GAS TypeAttaching Speed Control to Firebox Model BKT Installation Blower Wiring DiagramInstalling GAS Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Fireplace Gas Connections Cleaning Glass DoorREMOVING/REPLACING Glass Door Removing Louver PanelsInstalling LOGS, Lava Rock and Glowing Embers Installing Left Side and Top Brick PanelsInstalling Log No Wall Switch Installation Wiring DiagramOptional Remote Control For Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS To ApplianceOperating Optional Blower Accessory Pilot AssemblyInspecting Burners Burner Flame PatternCleaning Maintenance Glass DoorPilot and Burners LogsTroubleshooting Observed Problem Possible Cause RemedyGas leak. See Warning statement at TopReplacement Parts Service Hints SpecificationsTechnical Service Parts Under WarrantyAccessories Illustrated Parts Breakdown Parts List VV36EPS VV36EPH Description QTYBurner Assembly for Models KEY Part Number Description QTY VV42EN, VV42ENS, VV42ENH VV42EP, VV42EPS, VV42EPH VV42ENS VV42ENH Illustrated Parts Breakdown KEY Part Number Description QTY Warranty Information

(V)V36EN specifications

Desa (V)V36EN is a cutting-edge technological solution that combines advanced features and innovative capabilities to enhance user experience and operational efficiency. This state-of-the-art product is designed to cater to a wide range of applications, making it an essential tool across various industries.

One of the standout features of the Desa (V)V36EN is its robust and flexible architecture. This design allows for seamless integration with existing systems, minimizing downtime during implementation and maximizing productivity from the get-go. The system is engineered to support various communication protocols, ensuring compatibility with numerous devices and platforms. This versatility makes it a valuable asset for businesses looking to streamline processes and improve connectivity.

In terms of performance, the Desa (V)V36EN boasts impressive processing capabilities. It utilizes high-speed processors that enable rapid data analysis and decision-making, thereby optimizing workflows. Additionally, featuring advanced data management technologies, the system can handle large volumes of data efficiently. This ensures that users can access critical information in real-time, empowering them to make informed decisions quickly.

Security is another paramount feature of the Desa (V)V36EN. With built-in security protocols and encryption technologies, the system safeguards sensitive information against unauthorized access and cyber threats. This focus on security not only protects business data but also enhances user trust, making it a reliable choice for organizations across various sectors.

User-friendliness is a key characteristic of the Desa (V)V36EN. The intuitive interface ensures that users can navigate the system with ease, requiring minimal training to operate effectively. This aspect significantly reduces the learning curve, allowing teams to adopt the technology rapidly and start reaping the benefits.

Finally, the Desa (V)V36EN is designed with scalability in mind. As businesses grow and evolve, the system can be easily updated and expanded to accommodate increasing demands. Whether it’s integrating new features or scaling up operational capabilities, this flexibility makes it a long-term solution for organizations seeking innovation.

In conclusion, the Desa (V)V36EN stands out as a comprehensive technological solution that combines flexibility, performance, security, user-friendliness, and scalability. It is an ideal choice for organizations looking to improve efficiency, enhance productivity, and stay ahead in a competitive landscape.
Top Page Image Contents