Desa VDCFRNB, VDCFTPB, VDCFRPB For Built-In Installation, Extension Cord, Blower Bracket

Page 15

INSTALLATION

Continued

For Built-In Installation

WARNING: A licensed elec- trician must connect the wiring harness to electrical supply following all local codes. Electri- cian must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of fireplace.

1.Install snap bushing from blower kit into one hole on rear of remote/blower bracket (see Figure 17). The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Accessory, page 14.

3.A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 18).

4.Plug power cord to outlet receptacle (not provided) as shown in Figure 17. Wind the extra power cord and tie with plastic wire strap (see Figure 17). Set power cord bundle between the remote/blower bracket and outer casing, away from the burner.

5.Test to make sure blower is working properly.

6.Reinstall upper louver beginning with bottom screws (see Figure 11, page 12) and close lower louver.

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole re- ceptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An undersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

	Fan Switch
	(Auto/Off/On)
		1 Auto
	Off	2
		3			Blue		Thermostat
			On					Switch
			On					(N.O.)
110/115			Red						Blue
V.A.C.			Red						Blower
	Black									Motor
	Black							Red
								Red
	White							White
	Green							Green

Figure 18 - Wiring Diagram For Blower

Accessory Built-In Installation

Blower Bracket	Wire Harness
Blower Bracket
Assembly
Screw

Power Cord

Switch

Outlet Receptacle (not included)

3 2 1

Switch

Plate

Plastic Wire Strap Wire Harness

Lower Louver Door

Clamp Connector (not included)

Remote/ Blower Bracket

Figure 17 - Installing Blower Bracket Assembly

116526-01B

www.desatech.com

15

Image 15

Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory Thermostat Models Vdcftnb and Vdcftpb Remote-Ready ModelsVdcfrpb and Vdcfrnb Table of Contents Safety Information Safety Information Local Codes Optional Remote Control AccessoriesProduct Features Product IdentificationAir for Combustion Ventilation Hood AssemblyAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationMinimum Clearance to Combustible Materials InstallationInstallation Items Fireplace ClearancesDepth Built-In Fireplace InstallationActual Framing Height Front WidthTop Louver Bottom Louver Optional Mantel InstallationMantel Shelf Side of FireboxRemoving Upper Louver Installing Optional Blower Accessory GA3450TAInstalling Blower Accessory Remote Blower Bracket Switch Plate ScrewOpen lower louver door by swinging door down see , For Built-In Installation Extension CordBlower Bracket Connecting to GAS Supply Connecting equipment shutoff valve to heater control Installation Items NeededChecking GAS Connections Gas Meter Pressure Testing Fireplace Gas ConnectionsEquipment Open Shutoff Valve Closed Gas Regulator or Gas Control Valve EquipmentInstalling Receiver Receiver Volt Terminal Battery Wires Battery ClipInstalling 9-Volt Battery in Hand-Held Remote Control Unit Terminal W Terminal R Optional Wall Switch GWMS2 Remote-Ready Models OnlyControl Valve To Wall Thermostat or Switch Feed wires through rectangular slotsLighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceThermostat Control Operation Manual Lighting ProcedureOperating Fireplace To Turn OFF GAS To ApplianceOperating Blower AUTO/OFF/ON SwitchPiezo Flame Control Ignitor Button Adjustment Knob Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode HRC200 Optional Hand-HeldRemote Operation Thermostat Series ModelOptional GWMT1 Wall mounted Thermostat Optional GWMS2 Wall Mounted SwitchBurner Flame Pattern Cleaning MaintenanceInspecting Burners Pilot Flame PatternCabinet Cleaning MaintenanceWiring Diagram LOG SetObserved Problem Possible Cause Remedy TroubleshootingTroubleshooting Initial operation Processes and log curing When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning Rating Variable 17,000/26,000 Btu/Hr SpecificationsThermostat Models Remote-Ready Models Rating Variable 17,000/30,000 Btu/HrFirebox Models VDC Illustrated Parts BreakdownOuter Casing Parts ListOuter Casing Top BaffleIllustrated Parts Breakdown Thermostat ModelsVdcftpb and Vdcftnb Parts List Vdcfrnb and Vdcfrpb REMOTE-READY ModelsBrass Flare Adapter Fitting Accessories Equipment Shutoff Valve GA5010THERMOSTAT-CONTROLLED Blower KIT GA3450T Accessories WALL-MOUNT ON/OFF SwitchWALL-MOUNT Thermostat Parts Under Warranty Replacement PartsService Hints Technical Service116526-01B Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth