Desa V42V-A Vertical Termination Configurations, Venting with One 90 Elbow, Vertical Venting

Page 13

Venting Installation

instructions

Continued

Vertical Termination Configurations

Figures 21 through 24 show four different configurations for verti- cal termination.

Venting with Two 90° Elbows

Vertical (V)	Horizontal (H1) +
	Horizontal (H2)
5' min.	2' max.
6' min.	4' max.
7' min.	6' max.
8' min.	8' max.
20' max.	8' max.

45° Elbow

Note: Install restrictor into inner collar of fireplace as shown.

Figure 21 - Vertical Venting Configuration Using Two 90° Elbows with Two Horizontal Runs (Vertical Round High Wind Termination Shown)

Venting with One 90° Elbow

	Vertical (V)	Horizontal (H)
	5' min.	2' max.
	6' min.	4' max.
	7' min.	6' max.
	8' min.	8' max.
45° Elbow	20' max.	8' max.
45° Elbow

Note: Install restrictor into inner collar of fireplace as shown.

Figure 22 - Vertical Venting Configuration Using One 90° Elbow (Vertical Round High Wind Termination Shown)

Venting with Two 90° Elbows

Vertical (V1)	Horizontal (H)
5' min.	6' max.
6' min.	12' max.
7' min.	18' max.
8' min.	20' max.

Note: Install restrictor into inner collar of

fireplace as shown.

45° Elbow

Note: Vertical (V1) + Vertical (V2) = 40' max.

Figure 23 - Vertical Venting Configuration Using Two 90° Elbows (Vertical Round High Wind Termination Shown)

Vertical Venting

V = 40' max.

Note: Install restrictor into inner collar of fireplace as shown.

45° Elbow

Figure 24 - Vertical Venting Configuration With No Horizontal

Run (Vertical Round High Wind Termination Shown)

111906-01F

www.desatech.com

13

Image 13

Contents What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsProduct Identification Product FeaturesLocal Codes Location and space requirements Pre-Installation PreparationClearances Framing and finishing Framing Clearances for Installation Against an Exterior WallTermination CAP AIR Supply Inlet GAS Meter Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Horizontal Termination InstallationVent Pipe Connections Vent pipe before connecting horizontal run to vent cap see Ground Floor Installation Horizontal Termination ConfigurationsVenting with Two 90 Elbows Snorkel Termination InstallationOffset with Wall Strap and 45 Elbows Flat Ceiling InstallationVenting with One 90 Elbow Vertical Termination ConfigurationsVertical Venting High Altitude Installation Fireplace InstallationParts lists for venting kits and components Installing optional blower accessoriesAttaching Speed Control to Firebox Model BKT InstallationBlower Wiring Diagram Installing Gas Piping to Fireplace LocationInstallation Items Needed Installation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Fireplace Gas Connections Installing Remote ReceiverCleaning Glass Door Installing Brick liner Models BL42DASA and BL42DHASARemoving/Replacing Glass Door Removing Louver PanelsInstalling Rear Brick Panel Installing logs, lava rock Glowing embersOperating Fireplace For your safety read Before lightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureOpTIONAL Hand-Held Remote OperationThermostat Series Model HRC200 Operating optional blower accessoryOperating optional GWMT1 Wall Mounted Thermostat Pilot assembly Cleaning MaintenanceInspecting Burners Burner Flame PatternTo clean pilot. This can damage pilot unit TroubleshootingPilot and burners LogsTroubleshooting Above Gas leak. See Warning statementService Hints Replacement PartsTechnical Service SpecificationsAccessories Illustrated Parts Breakdown 108331-01 108331-02 109082-02 Parts ListIllustrated Parts Breakdown VV42PHB1 and CHDV24NR-B 111906-01F 111906-01F Keep this Warrant Warranty Information