![](/images/new-backgrounds/1002867/286711x1.webp)
REQUIRED CLEARANCE FOR UNIT INSTALLATION
AND ROOF PENETRATION HOLE SIZE REQUIRED
6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D |
| A |
|
|
|
|
|
|
|
|
| |
|
|
| SERVICE |
|
|
|
| SERVICE | |
|
|
| CLEARANCE |
|
|
|
| CLEARANCE | |
|
|
| LINES |
|
|
|
| LINES | |
|
|
|
|
|
|
| SUPPLY AIR |
|
|
|
|
|
|
|
|
| C | RETURN AIR | B |
|
|
|
|
|
|
|
| ||
|
| SIDE RAIL |
|
|
|
|
|
| |
|
| WOOD NAILER |
|
|
|
|
| ||
SERVICE CLEARANCE & PENETRATION DIMENSIONS |
|
|
| ||||||
MODEL NO. | A | B | C | D | E | F | HOLE IN ROOF |
|
|
30" | 30" | *12" | 24" | 36" | 25" |
|
|
| |
30" | 30" | *12" | 30" | 44" | 25" |
|
|
| |
42" | 30" | *12" | 36" | 50" | 25" | E |
| F | |
|
|
|
|
|
|
|
|
| |
* 18" WITH FRESH AIR ACCESSORY |
|
|
|
|
|
| |||
* 30" WITH ECONOMIZER |
|
|
|
|
|
|
|
|
LOCATIONS AND RECOMMENDATIONS
These units are designed for outdoor installation. For proper instal- lation, the following recommendations must be considered.
NOTE: Unit shipped for horizontal installation. Convert to downflow per instruction.
The discharge air from the condenser fans must be unrestricted for a minimum of 3 feet above the unit.
Roof Mounting Curb (field assembled BAYCURB030A and BAYCURB033A, BAYCURB034A) or a field fabricated curb must be in place before unit is hoisted to the roof.
Roof Mounting Curb (frame) must be installed on a flat, level section of the roof (max. of 1/4" per foot pitch), providing a level mounting surface for the unit. In addition, provide sufficient height above the roof to prevent water from entering unit.
In locations where deep snows are encountered,RAlSE THE UNlT A MINIMUM OF 12" OFF THE ROOF, DECK OR
Roof Mounting Curb used with
AVOID LOCATING THE UNIT WHERE SNOW TENDS TO DRIFT. This will reduce the times when it is necessary for the customer to remove the snow from around the unit. MAKE CERTAIN THE CUSTOMER KNOWS THAT SNOW ACCUMULATIONS SHOULD BE REMOVED FROM THE SIDES OF THE UNIT FOR BEST EFFICIENCY.
A snow drift barrier may be installed around the unit to prevent a build up of snow on the sides of the unit. The barrier should be of sufficient distance from the unit to prevent restriction of airflow to and from unit.
LOCATE THE UNIT SO THAT THE WATER VAPOR THAT DIS- CHARGES UPWARD DURING DEFROST DOES NOT CONDENSE ON WINDOWS AND FOG THEM OR CAUSE ICICLES TO FORM ON OVERHANGS.
1.Be sure the mounting curb spans structural members (trusses) of the roof, thereby providing sufficient support for weight of the unit, curb and duct(s) plus any accessories (factory or field installed). See Figures 1, 2, 3, 4, 5, 6, 7, 8, 9,10,11 and 12.
NOTE: If any internal accessories are to be added to the unit it should be done at the shop if at all practical.
2.Unit should be positioned so
Page 6