Brinkmann 810-6830-0 owner manual Cleaning and Maintenance, Burner ASSEMBLY/MAINTENANCE

Page 15

CLEANING AND MAINTENANCE:

Keep the appliance free and clear of combustible materials, gasoline and other flammable vapors and liquids.

Keep the ventilation openings free and clear of debris.

Visually check burner flames for proper operation (see pictorial in "Burner Assembly/Maintenance" under Proper Care and Maintenance). Spiders or other insects can nest in the burner causing gas blockage.

For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended periods of storage.

Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year.

CAUTION! Some parts may contain sharp edges. Wear protective gloves if necessary.

Remove the cooking grills, heat distribution plates, and burners from inside your grill. Use a brush with hot water and detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse completely with water. Towel dry and replace all components as described in the assembly instructions.

BURNER ASSEMBLY/MAINTENANCE

Although your burners are constructed of brass, they may rust as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage. If found, replace the burner.

DO NOT obstruct the flow of combustion and ventilation air. Burner tubes can become blocked by spiders and other insects building their nests. Blocked burner tubes can prevent gas flow to the burners and could result in a burner tube fire or fire beneath the grill. To clean the Burner Assembly follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.Turn gas off at control knobs and natural gas supply.

2.Remove cooking grills and heat distribution plates.

3.Remove cotter pins from beneath each burner

“foot” using a screwdriver or needle nose pliers.

4. Carefully lift each burner up and away from valve openings.

Debris

5. Use a narrow bottle brush or a stiff wire bent

into a small hook to run through each burner tube and flame port several times.

Note: Wear eye protection when performing procedure 6.

6.Use compressed air to blow into burner tube and out the flame ports. Check each port to make sure air comes out each hole.

7.Wire brush entire outer surface of burner to remove food residue and dirt.

8.Check burner for damage, if any large cracks or holes are found replace burner.

IMPORTANT: Burner opening must slide over valve nozzle.

9.Carefully replace burners.

10.Replace cotter pins beneath each burner and follow the "Gas Leak Testing" section of this manual. Relight burners to verify proper operation.

11.Replace heat distribution plates and cooking grills.

Valve Nozzle

Burner Orifice

PROPER BURNER OPERATION

14

Image 15
Contents Natural GAS Grill Island Important Safety Table of Contents General Warnings Installation Information Disconnecting Your Grill from the Natural GAS Source Connecting Your Grill to the Natural GAS SourceLeak Testing When to Perform a Leak TestChecking for Leaks PRE-START Check List Lighting Instructions Lighting the Main BurnersMatch Lighting the Main Burners Lighting the Rotisserie Burner Match Lighting the Rotisserie BurnerLighting the Side Burner Turning OFF the Grill Match Lighting the Side BurnerControlling FLARE-UPS Operating the GrillBreaking in Your Grill Preheating the GrillSide Burner Rotisserie CookingCleanliness Grilling to Proper TemperatureHelpful Hints Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceBefore Storing Your Grill Cooking GrillsHeat Distribution Plates Transporting and StorageTrouble Shooting Frequently Asked Questions Parts BAG Contents Assembly Instructions For Missing PARTS, Please Call Customer Service AT Step Guide Pin Extension Cord Hole Step Support Plates Threaded Stud Washer M8 Nut Step M6 x 12mm bolt Step Attach basket bracket guide using two M5 x 10mm bolts Side Burner Place side burner grate on side burner Charmglow Grill Island Assembled DE Seguridad Índice Advertencias Generales Informations Concernant L’INSTALLATION Desconectar SU Parrilla DE LA Fuente DE GAS Natural Conectando SU Parrilla a LA Fuente DE GAS NaturalPruebas DE Detección DE Fugas Cuándo Realizar UNA Prueba DE Detección DE FugasVerificación DE Ausencia DE Fugas Lista DE Verificación Preliminar AL Encendido Instrucciones DE Encendido Encendido DE LAS Hornillas PrincipalesEncendido DE LAS Hornillas Principales CON UN Cerillo Encendido DE LA Hornilla Lateral Encendido DE LA Hornilla DEL Asador Estilo RotisserieApagado DE LA Parrilla Encendido DE LA Hornilla Lateral CON UN CerilloControl DE LAS Llamaradas Operación DE LA ParrillaPreparación DE LA Parrilla Para Usarla POR Primera VEZ Precalentamiento DE LA ParrillaLA Hornilla Lateral Cocción Estilo RotisserieLimpieza Cocinar a LA Parrilla a LA Temperatura ApropiadaRecomendaciones Útiles INSTALACIÓN/MANTENIMIENTO DE LAS Hornillas Limpieza Y MantenimientoAntes DE Guardar LA Parrilla Rejillas Para CocinarPlacas DE Distribución DEL Calor Transporte Y AlmacenajePreguntas Frecuentes Identificación Y Corrección DE ProblemasPreguntas Frecuentes Instrucciones DE Armado SI Faltan PARTES, Llame a Servicio AL Cliente AL Contenido DE LA Bolsa DE Partes Paso Pasador de Guía Orificio para el Cable de Extensión Nota Asegúrese de que la flecha esté apuntando hacia delante Placas de Apoyo Perno prisionero roscado Arandela Tuerca M8 Paso Perno M6 x 12mm Paso Tuerca M6 Pasador de resorte Pasador de bisagra Side Burner Coloque la rejilla en la hornilla lateral Charmglow Grill Island Armada Warranty