Teledyne 3000TA operating instructions Application notes, Flow Rate Recommendations

Page 83

Trace Oxygen Analyzer

Appendix

 

 

 

A.5 Application notes

3000 SERIES ANALYZERS

APPLICATION NOTES ON PRESSURES AND FLOW RECOMMENDATIONS

The 3000 series analyzers require reasonably regulated sample pressures. While the 3000 analyzers are not sensitive to variations of incoming pressure provided they are properly vented to atmospheric pressure. The pressure must be maintained as to provide a useable flow rate trough the analyzer. Any line attached to sample vent should be 1/4 or larger in diameter.

FLOW RATE RECOMMENDATIONS:

A usable flow rate for a 3000 series analyzer is one which can be measured on the flowmeter. This is basically .2-2.4 SLPM. The optimum flow rate is 1 SLPM (mid scale).

Note: Response time is dependent on flow rate, a low flow rate will result in slow response to O2 changes in the sample stream. The span flow rate should be the approximately same as the sample flow rate.

CELL PRESSURE CONCERNS:

The sensors used in 3000 series analyzers are optimized to function at atmospheric pressure. At pressures other than atmospheric the diffusion rate of O2 will be different than optimum value. Higher pressures will produce faster O2 diffusion rates resulting in higher O2 reading and shorter cell life. To use a 3000 series analyzer at a cell pressure other than atmospheric, the analyzer must be calibrated with a known calibration gas at the new cell pressure to adjust for the different diffusion rate. Cell pressures below 2/3 atmospheric are not recommended because they tend to cause excessive internal expansion which may result in seal failure.

For operation at cell pressures other than atmospheric, care must be taken not to change the sample pressure rapidly or cell damage may occur. For cell pressures above atmospheric, caution must be exercised to avoid over pressuring the cell holder. (Percent analyzers will require some type of cell retainer to prevent the cell from being pushed out by

 

 

 

Teledyne Analytical Instruments

71

Image 83
Contents Teledyne Analytical Instruments Model 3000TACopyright 2011 Teledyne Analytical Instruments 3000TA- EUTrace Oxygen Analyzer Specific Model InformationImportant Notice Safety Messages 3000TA- EU Vii Table of Contents Operation MaintenanceAppendix Model 3000TA Front Panel List of FiguresList of Tables Typical Applications Main Features of the AnalyzerIntroduction OverviewIntroduction 3000TA- EU Model DesignationsModel 3000TA Front Panel Front Panel Operator InterfaceRecognizing Difference Between LCD & VFD ∙ 50-Pin Equipment Interface Port Rear Panel Equipment InterfaceIntroduction 3000TA- EU Trace Oxygen Analyzer Operational Theory Operational TheoryIntroduction Micro-Fuel Cell SensorAnatomy of a Micro-Fuel Cell Operational Theory 3000TA- EUElectrochemical Reactions Effect of Pressure Calibration CharacteristicsSample System Characteristic Input/Output Curve for a Micro-Fuel CellPiping Layout and Flow Diagram for Standard Model Flow Diagram Electronics and Signal Processing3000TA Internal Electronic Component Location Block Diagram of the Model 3000TA-EU Electronics Operational Theory 3000TA- EU Mounting the Analyzer InstallationTrace Oxygen Analyzer Installation Unpacking the AnalyzerFront Panel of the Model 3000TA Installation 3000TA- EUGas Connections Rear Panel ConnectionsSample Electrical Connections Exhaust OUTEquipment Interface Connector Pin Arrangement ∙ Threshold Alarm Alarm Relay Contact Pins Pin Function Range ID Relay Connections 2.3 RS-232 Port Remote Probe ConnectionsCommands via RS-232 Input Testing the System Installing the Micro-Fuel CellPage Trace Oxygen Analyzer Operation Using the Data Entry and Function ButtonsOperation Operation 3000TA- EU Hierarchy of Functions and Sub functions System FunctionTracking Oxygen Readings During Calibration and Alarm Delay TRAK/HLD Auto-Cal Pswd Logout More Setting up an Auto-Cal Password Protection A a a Characters Available for Password Definition Logout System Self-Diagnostic Test Showing Negative Oxygen Readings Version ScreenZero and Span Functions Zero Cal Zero Settling Man ENT To Begin Span Cal Span Val 000008.00 ENTSpan UPMod # #### % Span Slope=#### ppm/s Span Failure Alarms FunctionAL-1AL-2 Choose Alarm Range Function Setting the Analog Output Ranges Fixed Range Analysis Analyze Function Signal OutputMED Operation 3000TA- EU Teledyne Analytical Instruments Storing and Handling Replacement Cells MaintenanceRoutine Maintenance Trace Oxygen Analyzer MaintenanceRemoving the Micro-Fuel Cell Maintenance 3000TA- EUWhen to Replace a Cell Removing the Micro-Fuel Installing a New Micro-Fuel CellMaintenance 3000TA- EU Cell Warranty Fuse ReplacementInstalling Fuses System Self Diagnostic TestMajor Internal Components Troubleshooting CleaningTrace Oxygen Analyzer Maintenance Maintenance 3000TA- EU Teledyne Analytical Instruments Trace Oxygen Analyzer Appendix Model 3000TA SpecificationsAppendix Appendix 3000TA- EU Recommended 2-Year Spare Parts ListOrders should be sent to 19-inch Relay Rack Panel Mount Drawing ListFlow Rate Recommendations Application notes3000TA Examples Bypass Conversions Section II Physical and Chemical Data Material Safety Data SheetSection I Product Identification Section IV Health Hazard Data Appendix 3000TA- EU Section III -Physical HazardsSection VI Handling Information
Related manuals
Manual 19 pages 17.56 Kb

3000TA specifications

The Teledyne 3000TA is an advanced telemetry system designed for high-performance applications in various industries such as aerospace, automotive, and research. This innovative device combines cutting-edge technologies with user-friendly features, making it an essential tool for engineers and scientists alike.

One of the standout features of the Teledyne 3000TA is its robust data acquisition capabilities. It offers a high sampling rate, which allows users to capture rapid changes in measurements accurately. This is particularly beneficial for applications that require real-time data analysis and decision-making, such as testing the performance of new aircraft components or monitoring engine behavior under different loads.

The 3000TA integrates multiple sensor interfaces, enabling it to connect seamlessly with various types of sensors, including temperature, pressure, and strain gauges. This versatility makes it suitable for a wide range of testing scenarios, from structural analysis to environmental monitoring. Users can customize the system to fit their specific needs, significantly enhancing its functionality.

Another significant advantage of the Teledyne 3000TA is its advanced wireless communication technology. By employing protocols like Bluetooth and Wi-Fi, it allows for remote data monitoring and access, which improves safety and convenience during testing processes. Engineers can easily gather data from hazardous environments without being physically present, ensuring both efficiency and safety.

The device is also equipped with an intuitive user interface, which simplifies the setup and operation processes. The touchscreen display provides real-time data visualizations and easy navigation through various menus, making it accessible even to those new to telemetry systems. This user-centric design reduces the learning curve and enhances overall productivity.

In terms of data integrity, the Teledyne 3000TA features robust error-checking and validation protocols. These built-in safeguards ensure that the data collected is accurate and reliable, which is crucial for making informed decisions based on telemetry data.

The system's compact and lightweight design ensures portability, allowing for use in various fields and environments. This flexibility enhances its appeal for field applications, where space and weight can be significant constraints.

In summary, the Teledyne 3000TA stands out as a versatile and reliable telemetry solution, combining high-performance data acquisition, advanced communication technologies, and user-friendly features. Its application across multiple industries makes it an invaluable tool for professionals seeking to optimize their testing and analysis processes.