Agilent Technologies 54600-Series manual Trigger System, Pulse Width

Performance Characteristics (continued)

Horizontal (continued)

Digital Delta-t Accuracy	54621A/D, 54622A/D, 54624A:
(non-Vernier settings)	Same Channel: ±0.01% reading ±0.1% screen width ±(1 digital sample period, 2.5 or 5 ns
	based on sample rate of 200/400 MSa/s)
	Channel-to-Channel: ±0.01% reading ±0.1% screen width ±(1 digital sample period, 2.5 or 5 ns)
	±chan-to-chan skew (2 ns typical, 3 ns maximum)
	54641A/D, 54642A/D:
	Same Channel: ±0.005% reading ±0.1% screen width ±(1 digital sample period, 1ns)
	Channel-to-Channel: ±0.005% reading ±0.1% screen width ±(1 digital sample period) ±chan-to-chan skew
	Same Channel Example (54641A/D, 54642A/D):
	for signal with pulse width of 10 µs, scope set to 5 µs/div (50 µs screen width),
	delta-t accuracy = ±{.005%(10 µs) + 0.1%(50 µs) + 1 ns} = 51.5 ns
Delay Jitter	<1 ppm
RMS Jitter	0.025% screen width + 30 ps
Modes	Main, Delayed, Roll, XY
XY	Bandwidth: Max bandwidth
	Phase error @ 1 MHz: 1.8 degrees
	Z Blanking: 1.4 V blanks trace (use external trigger) - 54621A/D, 54622A/D, 54624A only
Trigger System
Sources:	54621A/622A, 54641A/642A: Ch 1, 2, line, ext
	54621D/622D, 54641D/642D: Ch 1, 2, line, ext, D15 - D0
	54624A: Ch 1, 2, 3, 4, line, ext
Modes	Auto, Triggered (normal), SingleAuto level (54621A/D, 54622A/D, 54624A only)
Holdoff Time	~60 ns to 10 seconds
Selections	Edge, Pulse Width, Pattern, TV, Duration, Sequence, CAN, LIN, USB, I2C, SPI
Edge	Trigger on a rising or falling edge of any source
Pattern	Trigger on a pattern of high, low, and don’t care levels and/or a rising or falling edge established across any of the sources.
	The analog channel’s high or low level is defined by that channel’s trigger level.
Pulse Width	Trigger when a positive- or negative-going pulse is less than, greater than, or within a specified range on any of
	the source channels.
	Minimum pulse width setting: 5ns (2 ns on 54641A/D, 54642A/D analog channels)
	Maximum pulse width setting: 10 s
TV	Trigger on any analog channel for NTSC, PAL, PAL-M, or SECAM broadcast standards on either positive or negative
	composite video signals. Modes supported include Field 1, Field 2, or both, all lines, or any line within a field. Also supports
	triggering on non-interlaced fields. TV trigger sensitivity: 0.5 division of synch signal.
Sequence	Arm on event A, trigger on event B, with option to reset on event C or time delay.
CAN	Trigger on CAN (Controller Area Network) version 2.0A and 2.0B signals. It can trigger on the Start of Frame bit of a data
	frame, a remote transfer request frame, or an overload frame.
LIN	Trigger on LIN (Local Interconnect Networking) sync break at beginning of message frame.
USB	Trigger on USB (Universal Serial Bus) Start of Packet, End of Packet, Reset Complete, Enter Suspend, or Exit Suspend on
	the differential USB data lines. USB low speed and full speed are supported.

* Denotes Warranted Specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ±10 °C from firmware calibration temperature.

16