Sunrise Medical V-521 Ramps AT Home & Work, Wheelchair Lifts, Curbs & Single Steps, Stairs

Page 10

V I .

G E N E R A L W A R N I N G S

 

 

U. RAMPS AT HOME & WORK

Make sure ramps meet all Building Codes for your area.

1.For your safety, have a licensed contractor build or remodel ramp to meet all standards.

2.Note: The proper design will vary, depending on such things as: the length and height of the ramp; the need for an intermediate platform; landing size; doors, and the direction of swing, and; whether the ramp includes a turn or angle.

Note: Failure to follow these warnings may result in a fall and possible injury.

At A Minimum:

1.Open sides of ramp must have side rails to prevent your chair from going over the edge.

2.Slope must not be steeper than one inch in height for every one foot of slope length.

3.Ramp surface must be even, and have a non-skid surface.

4.You may need to add a section at the top or bottom to avoid a lip or drop-off.

5.Ramp must be sturdy. Add bracing if needed, so ramp does not “bow” when you ride on it.

V. WHEELCHAIR LIFTS

Wheelchair lifts are used in vans, buses, and buildings to help you move from one level to another.

1.Always turn off all power to your chair when you are on a lift. If you fail to do so, you may touch the joystick by accident and cause your chair to drive off the platform. (Be aware that a “roll-stop” at the end of the platform may not prevent this).

2.Make sure there is not a lip or drop-off at the top or bottom of the platform. These may cause a fall or tip-over.When in doubt, have someone help you.

3.Always secure the rider with a positioning belt to help prevent falls during transfers.

4.Avoid moving forward if a wheel is “hung up” on the lip of the ramp. Backup, reposition the caster for a more direct approach. And slowly try again.

930485 Rev. A

18

V I .

G E N E R A L W A R N I N G S

 

 

W. CURBS & SINGLE STEPS

1.Your chair is not designed to drive up or down a curb or step more than 2" high. Doing so may:

Result in a fall or tip-over.

Damage the frame, wheels, axles or other chair parts, or loosen fasteners.

2.To prevent a fall or tip-over, use wheelchair access ramps or have someone help you.

3.If you must climb or descend a curb or step alone do so at your own risk and use extreme care.

Go as straight up or straight down as you can. Never turn or climb or descend at an angle as a fall or tip-over is likely.

Proceed slowly, at a steady speed.

4.Make sure that persons who assist you review the “Tips For Attendants” and heed all warnings.

X.STAIRS

Never use this chair to go up or down stairs, even with an attendant. Doing so is likely to cause a fall or tip-over.

Y.ESCALATORS

Never take this chair on an escalator, even with an attendant. Doing so is likely to cause a fall or tip-over.

19

930485 Rev. A

Image 10
Contents Quickie For Answers to Your Questions Sunrise ListensSunrise Home Healthcare Group Mobility Products Division EMI Electromagnetic InterferenceMaintenance Chart Check-Out To Find & Correct a ProblemConnecting Batteries in Battery Boxes Positioning Belts OptionalQuickie Choose the Right Chair & Safety OptionsAdjust Chair to Your Ability Review this Manual OftenSources of EMI What is EMI?What Effect can EMI HAVE? Distance from the SourceSafety CHECK-LIST Weight LimitController Settings Changes & AdjustmentsEnvironmental Conditions When Seated in a Parked WheelchairMotor Vehicle Safety TerrainTo Reduce the Risk AND/OR Damage to the Chair TransfersReaching or Leaning Dressing or Changing ClothesRAMPS, Slopes & Side Hills ObstaclesDriving in Reverse BewareCurbs & Single Steps Ramps AT Home & WorkWheelchair Lifts StairsArmrests ON/OFF SwitchANTI-TIP Levers BatteriesRear Wheel Locks Optional Positioning Belts OptionalPush Handles Seating SystemsTo Climb a Curb or Single Step To Descend a Curb or Single StepCHECK-OUT To Find & Correct ProblemTools YOU will Need SWING-AWAY FootrestsHEIGHT-ADJUSTABLE Armrests Optional Integral Joystick InstallationDUAL-POST HEIGHT- Adjustable Armrests Elevating Legrest OptionalQuickie Qtronix Programming PAD Optional Control SettingsFolding and Unfolding Circuit Breakers Thermal ROLL-BACKIntegral Joystick Use Proper Batteries Joystick Boot HIntroduction BreakingLift battery into battery box base Battery ChargerConnecting Batteries in Battery Boxes Tighten all the terminal fasteners using two wrenchesMake sure to allow enough time to fully charge batteries Charging BatteriesDisposing of Batteries Battery Maintenance CleaningStorage Tips Motor Brushes Maintenance ChartTo Repair or Replace a Tire Ordering PartsLimitations Additional WarrantyFor Life What WE will doSunrise Medical