Quantum Quantum 1402 Seat Position, To change the seat position, To adjust the seatback angle

Page 24

V . C O M F O R T A D J U S T M E N T S

10.Move the seat towers up or down to the desired height.

11.Reinstall the ball detent pin into each seat tower.

12.Reinstall the shroud.

13.Reinstall the trapeze bars and secure with the quick- release pins.

14.Reinstall the seat.

WARNING! Make sure the seat latch safety is flipped down before using the power chair.

15. Plug the controller connector(s) into the electronics tray.

Seat Position

You can move the seat forward or rearward by changing the extrusion mounting position.

To change the seat position:

1.Turn off the power to the controller.

2.Unplug the controller connector(s) from the electronics tray.

3.Remove the seat from the power base.

4.Remove both extrusions from the bottom of the seat.

5.Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 14.

6.Fasten the extrusions back onto the bottom of the seat.

7.Reinstall the seat.

8.Plug the controller connector(s) into the electronics tray.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release le- ver. This lever is located on the right side of the seat base.

To adjust the seatback angle:

1.Pull up on the seatback release lever.

2.Lean forward or backwards to the desired position.

3.Release the lever.

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.

To adjust the seatback angle:

Figure 14. Seat Position Adjustment

JAM NUT

ARMRESTANGLE

ADJUSTING SCREW

ARMREST HEIGHT

ADJUSTING

SETSCREWS

SEATBACK ANGLE

ADJUSTING SCREW

ARMREST

ADJUSTMENT

KNOB

Figure 15. Seatback and Armrest Adjustments

1.Remove the seatback angle adjusting screws from both seat hinges. See figure 15.

2.Set the seatback at the desired angle.

3.Reinstall the screws on both seat hinges and retighten.

24

www.quantumrehab.com

Quantum 1402

Image 24

Contents Quantum F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIISafety N T R O D U C T I O NPURCHASER’S Agreement Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y Pre-Ride Safety Check General GuidelinesModifications Weight Limitations Tire InflationIncline Information Freewheel Mode Braking InformationCornering Information Inclement Weather Precautions Public Streets and Roadways Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Stairs and Escalators DoorsElevators Lift/Elevation ProductsBatteries Transfers Prescription Drugs/Physical LimitationsAlcohol/Smoking Electromagnetic and Radio Frequency Interference EMI/RFI Quantum 1402 Power Chair I . Y O U R P O W E R C H a I RElectronics Tray Electronics TrayDual Manual Freewheel Levers To operate the dual manual freewheel leversActive-Trac Suspension Rear Suspension Rear Suspension SystemInitial Assembly Seat InstallationA S S E M B L Y To install the seat Power Seat Option InstallationTo install the power seat Comfort Adjustments You may need the following to make comfort adjust- mentsSeat Height/Angle Adjustment O M F O R T a D J U S T M E N T SManual Recline Seatback Adjustment To adjust the seatback angleSeatback Angle Adjustment Seat PositionArmrest Width Adjustment Armrest Angle AdjustmentArmrest Height Adjustment Controller PositionFoot Platform Height Adjustment Foot Platform Depth AdjustmentFoot Platform Angle Adjustment Power Elevating Seat Option If your power chair is equipped with a power elMatically. The power elevating seat is operated Evating seat, you can change the seat height autoAnti-tip Wheel Adjustment To adjust the anti-tip wheelsD I S a S S E M B L Y Seat RemovalFoot Platform Removal I . B a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging The Batteries To charge the batteries using the onboard charger To charge the batteries using the off-board chargerBattery Break-In Frequently Asked Questions FAQsWhat type of battery should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How can I get maximum range or distance per charge?How should I store my power chair and its batteries? What about public transportation?What about shipping? Care and Maintenance Should your power chair come in contact with waterTemperature I I . C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes Monthly ChecksDisposal of Your Power Chair Cleaning InstructionsWheel Replacement StorageBattery Replacement Quantum 1402 Drive WheelTo replace the battery When to See Your Quantum Rehab Specialist for ServiceCorrective Maintenance W a R R a N T Y Reconditioned Units Warranty Warranty ExclusionsService Checks and Warranty Service Exclusions also include components with damage caused byP E N D I X I Specification S Quantum 1402 Dimensions and Ground Clearance T E S T E S Quality Control Quantum