Pride Mobility Jazzy 1113 owner manual To remove the footrest, To disconnect the controller

Page 22

V . D I S A S S E M B L Y

To remove the footrest:

1.Remove the footrest by sliding the mountingbracket up the vertical bar of the front frame until the tabs on the mounting bracket can be pulled forward through the matching slots in the front frame. See figure 5.

To disconnect the controller:

1.At the rear of the Jazzy, disconnect the controller harness connectors from the electronics tray located at the well frame. You may need to pull firmly and gently wiggle the connector to remove it from the socket. For the smaller connector, you must squeeze the connector latch release levers to disconnect the connector from the socket. See figure 6.

To remove the seat:

1.Disconnect the controller harness connectors as previously described.

2.Push in the black spring-loaded seat frame latch release buttons (one on the front of each seat frame side tube). See figure 7.

3.While you are pushing both buttons or levers simultaneously, lift up on the front end of the seat frame.

4.Pull forward on the seat frame to release the locating pins from their slots in the rear seat post tower mounts. You may find it necessary to wiggle the frame gently from side to side to free the locating pins from their slots.

SLIDE FOOTREST UP AND PULL FORWARD TO REMOVE

Figure 5. Remove the Footrest

DISCONNECT JOYSTICK CONTROLLER

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

To remove the battery well frame:

1.Remove the seat as previously described.

2.Disconnect the battery case connectors (2) fromtheutilitytray. See figure 8.

3.Next, disconnect and remove the battery cases (with the batteries in them) from the battery well frame.

4.Disconnect the left motor connector from its matching socket located on the left frame assembly. Squeeze the connector latch release levers to disconnect.

5.Disconnect the right motor connector from its matching socket located on the right frame assembly. Squeeze the connector latch release levers to disconnect.

Figure 6. Joystick Controller Harness

SEAT FRAME LATCH RELEASE BUTTONS

Figure 7. Remove the Seat

22

www.pridemobility.com

US Jazzy 1113/Rev I/Feb03

Image 22

Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Introduction N T R O D U C T I O NInformation Exchange Pride Owners Club My Authorized Pride Provider IsS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Cornering InformationOutdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Elevators Public Streets and Roadways Stairs and EscalatorsDoors EMI & RFITransfers Motor Vehicle TransportPositioning Belts Inclement Weather Precautions Reaching and Bending BatteriesAlcohol Removable PartsAre all power chairs susceptible to EMI? EMI/RFI-FREQUENTLY Asked Questions FaqsWhere do radio waves come from? What is the FDA doing about the problem?What should I do if my power chair moves unexpectedly? T H E J a Z Z Y 1 1 1 JazzySpecifications Power Base Back View Power Base Assembly Manual Freewheel Levers To engage or disengage the drive motorsI S a S S E M B L Y To disassemble the JazzyTo disconnect the controller To remove the battery well frameTo remove the footrest To remove the seatTo disassemble the right frame assembly from the front frame To disassemble the left frame assembly from the front frameSeat Height and Angle C O M F O R T a D J U S T M E N T SArmrest Width Armrest Height Optional Armrest AngleController Extension Footrest Height Controller PositionFootrest Angle To adjust the anti-tip wheels Anti-Tip Wheel AdjustmentANTI-TIP Wheels I . a S S E M B L Y Frame AssembliesTo install the battery cases To install the battery well frameTo install the seat To mount the footrest Versa Seat or Versa Tilt OptionTo connect the controller Joystick I I . O P E R a T I O NVSI Controller KeypadOn/Off Key Battery Condition MeterSpeed/Profile Keys Actuator Key and Actuator Lights for optional equipment Controller ConnectorPin Charger Inhibit Connector Horn KeyTroubleshooting VSI Error CodesRemote Plus Controller Remote Plus Master RemotePower Accessory Indicator Mode KeySpeed Setting Indicator Right/Left Turn Indicator KeysOff-board Charger Socket Speed SettingsPower Accessories Controller Communications CableActuator Lighting Module Not Shown Power ModuleSleep Mode Trouble CodesDX Controller Out Of Neutral At Power UpEuropa Master Remote System Status Light To enable the lockout systemMagnetic Locking Area Drive Program Select Key Drive Mode andActuator Display also Remote Status DisplayBattery Saver Feature TochangethedrivemodeprogramSleep Mode If Enabled Fault CodesBatteries and Charging To charge the batteries by using the onboard chargerB a T T E R I E S a N D C H a R G I N G Charging Your BatteriesHow often must I charge the batteries? Battery BREAK-INCan I use a different battery charger? Daily UseWhy do my new batteries seem weak? What type of battery should I use?Battery Specifications How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my Jazzy 1113 and batteries? What about shipping?A R E a N D M a I N T E N a N C E Routine MaintenanceTemperature Should your Jazzy 1113 come in contact with waterWeekly Checks Daily ChecksTo check the brakes Monthly Checks Cleaning PrecautionsTo calibrate the joystick Remote Plus only Yearly ChecksTires and Tubes Drive WheelBattery Replacement To replace the batteriesMotor Brushes Corrective MaintenanceTo inspect or replace the motor brushes O P T I O N a L a C C E S S O R I E S SWING-AWAY Foot Rests SWING-AWAY Joystick BracketElevating LEG Rests Specialty Seating SystemsI . W a R R a N T Y Warranty Exclusions Damage caused byT E S T E S US Jazzy 1113/Rev I/Feb03 Quality Control-Model Pride keeps a more detailed report on file at the factory