Pride Mobility Jazzy 1113 To disassemble the right frame assembly from the front frame

Page 23

V . D I S A S S E M B L Y

6.Squeeze together the latch release levers that hang vertically down from the crossbar at the rear of the battery well frame. See figure 9. Lift up the rear end of the battery well frame. Pull it to the rear of the chair to release the front slots from the locating pins on the bottom bar of the front frame.

To disassemble the right frame assembly from the front frame:

1.Remove the battery well frame as previously described.

2.Stand behind the Jazzy and grasp the right frame assembly handle (located next to the front seat post tower) with your right hand.

3.Use your left hand and thumb to hold the front frame and press and hold (toward the center of the front frame) the silver-colored latch release lever. See figure 10.

4.Push the right frame assembly outward (toward the right) with your right hand holding the right frame assembly handle.

5.Pull up with your left hand on the front frame until the latching mechanism releases.

6.Keep pulling upward with your left hand until the locating pin on the bottom of that side of the front frame releases from its slot in the right frame assembly.

7.Carefully let the right frame assembly tilt to a resting position.

To disassemble the left frame assembly from the front frame:

1.Remove the battery well frame as previously described.

2.Stand behind the Jazzy and grasp the left frame assembly handle (located next to the front seat post tower) with your left hand.

3.Use your right hand and thumb to hold the front frame and press and hold (toward the center of the front frame) the silver- colored latch release lever. See figure 10.

4.Push the left frame assembly outward (toward the left) with your left hand holding the left frame assembly handle.

5.Pull up with your right hand on the front frame until the latching mechanism releases.

6.Keep pulling upward with your right hand until the locating pin on the bottom of that side of the front frame releases from its slot in the left frame assembly.

7.Carefully let the left frame assembly tilt to a resting position.

Figure 8. Disconnect Battery Cases

Figure 9. Front Frame

Figure 10. Front Frame

US Jazzy 1113/Rev I/Feb03

www.pridemobility.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Information Exchange N T R O D U C T I O NIntroduction My Authorized Pride Provider Is Pride Owners ClubModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Cornering Information Braking InformationStationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces EMI & RFI Public Streets and Roadways Stairs and EscalatorsDoors ElevatorsPositioning Belts Motor Vehicle TransportTransfers Batteries Inclement Weather Precautions Reaching and BendingRemovable Parts AlcoholWhat is the FDA doing about the problem? EMI/RFI-FREQUENTLY Asked Questions FaqsWhere do radio waves come from? Are all power chairs susceptible to EMI?What should I do if my power chair moves unexpectedly? Jazzy T H E J a Z Z Y 1 1 1Specifications Power Base Back View Power Base Assembly To engage or disengage the drive motors Manual Freewheel LeversTo disassemble the Jazzy I S a S S E M B L YTo remove the seat To remove the battery well frameTo remove the footrest To disconnect the controllerTo disassemble the left frame assembly from the front frame To disassemble the right frame assembly from the front frameArmrest Width C O M F O R T a D J U S T M E N T SSeat Height and Angle Controller Extension Armrest AngleArmrest Height Optional Footrest Angle Controller PositionFootrest Height ANTI-TIP Wheels Anti-Tip Wheel AdjustmentTo adjust the anti-tip wheels Frame Assemblies I . a S S E M B L YTo install the seat To install the battery well frameTo install the battery cases To connect the controller Versa Seat or Versa Tilt OptionTo mount the footrest Keypad I I . O P E R a T I O NVSI Controller JoystickSpeed/Profile Keys Battery Condition MeterOn/Off Key Horn Key Controller ConnectorPin Charger Inhibit Connector Actuator Key and Actuator Lights for optional equipmentVSI Error Codes TroubleshootingRemote Plus Master Remote Remote Plus ControllerRight/Left Turn Indicator Keys Mode KeySpeed Setting Indicator Power Accessory IndicatorController Communications Cable Speed SettingsPower Accessories Off-board Charger SocketTrouble Codes Power ModuleSleep Mode Actuator Lighting Module Not ShownEuropa Master Remote Out Of Neutral At Power UpDX Controller Magnetic Locking Area To enable the lockout systemSystem Status Light Tochangethedrivemodeprogram Drive Mode andActuator Display also Remote Status DisplayBattery Saver Feature Drive Program Select KeyFault Codes Sleep Mode If EnabledCharging Your Batteries To charge the batteries by using the onboard chargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingDaily Use Battery BREAK-INCan I use a different battery charger? How often must I charge the batteries?How can I get maximum range or distance per charge? What type of battery should I use?Battery Specifications Why do my new batteries seem weak?What about shipping? How can I ensure maximum battery life?How should I store my Jazzy 1113 and batteries? What about public transportation?Should your Jazzy 1113 come in contact with water Routine MaintenanceTemperature A R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Yearly Checks Cleaning PrecautionsTo calibrate the joystick Remote Plus only Monthly ChecksDrive Wheel Tires and TubesTo replace the batteries Battery ReplacementTo inspect or replace the motor brushes Corrective MaintenanceMotor Brushes O P T I O N a L a C C E S S O R I E S Specialty Seating Systems SWING-AWAY Joystick BracketElevating LEG Rests SWING-AWAY Foot RestsI . W a R R a N T Y Damage caused by Warranty ExclusionsT E S T E S US Jazzy 1113/Rev I/Feb03 Pride keeps a more detailed report on file at the factory Quality Control-Model
Top Page Image Contents