Pride Mobility Jazzy 1113 owner manual I . a S S E M B L Y, Frame Assemblies

Page 28

V I I . A S S E M B L Y

1.Place the three frame assemblies next to each other as shown in figure 18.

2.Stand behind the assemblies, grasp the front frame with your left hand, and fit the notch on the bottom bar of the front frame onto the locating pin on the lower section of the right frame assembly. (The frame is shown in figure 19.)

3.Pivot the front frame top bar toward the right frame assembly and, while holding the latch release lever, push the top bar of the front frame onto the locking mechanism until the two assemblies snap securely into place. Release the latch release lever to hold the two assemblies together.

NOTE: The front frame should be positioned with the two semicircular notches in the vertical bar facing forward.

4.Grasp the other frame assembly and lift the frame assembly into an upright position.

5.Tilt the front frame and the attached frame assembly (right side) so that the notch on the bottom bar of the front frame fits onto the locating pin on the bottom section of the other frame assembly (left side).You will also have to tilt the frame assembly (left side) slightly away from the front frame to make the parts fit together. See figure 20.

6.Pivot together the right frame assembly and the front frame, while holding the latch release lever, until the locking mechanism on the top bar of the front frame snaps securely to the left frame assembly. Release the latch release lever to hold the two assemblies together.

WARNING! Make certain that the front frame is snapped securely to both the right frame assembly and to the left frame assembly.

Figure 18. Frame Assemblies

Figure 19. Front Frame Assembly

28

www.pridemobility.com

US Jazzy 1113/Rev I/Feb03

Image 28

Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Introduction N T R O D U C T I O NInformation Exchange Pride Owners Club My Authorized Pride Provider IsS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Cornering InformationOutdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Public Streets and Roadways Stairs and Escalators DoorsElevators EMI & RFITransfers Motor Vehicle TransportPositioning Belts Inclement Weather Precautions Reaching and Bending BatteriesAlcohol Removable PartsEMI/RFI-FREQUENTLY Asked Questions Faqs Where do radio waves come from?Are all power chairs susceptible to EMI? What is the FDA doing about the problem?What should I do if my power chair moves unexpectedly? T H E J a Z Z Y 1 1 1 JazzySpecifications Power Base Back View Power Base Assembly Manual Freewheel Levers To engage or disengage the drive motorsI S a S S E M B L Y To disassemble the JazzyTo remove the battery well frame To remove the footrestTo disconnect the controller To remove the seatTo disassemble the right frame assembly from the front frame To disassemble the left frame assembly from the front frameSeat Height and Angle C O M F O R T a D J U S T M E N T SArmrest Width Armrest Height Optional Armrest AngleController Extension Footrest Height Controller PositionFootrest Angle To adjust the anti-tip wheels Anti-Tip Wheel AdjustmentANTI-TIP Wheels I . a S S E M B L Y Frame AssembliesTo install the battery cases To install the battery well frameTo install the seat To mount the footrest Versa Seat or Versa Tilt OptionTo connect the controller I I . O P E R a T I O N VSI ControllerJoystick KeypadOn/Off Key Battery Condition MeterSpeed/Profile Keys Controller Connector Pin Charger Inhibit ConnectorActuator Key and Actuator Lights for optional equipment Horn KeyTroubleshooting VSI Error CodesRemote Plus Controller Remote Plus Master RemoteMode Key Speed Setting IndicatorPower Accessory Indicator Right/Left Turn Indicator KeysSpeed Settings Power AccessoriesOff-board Charger Socket Controller Communications CablePower Module Sleep ModeActuator Lighting Module Not Shown Trouble CodesDX Controller Out Of Neutral At Power UpEuropa Master Remote System Status Light To enable the lockout systemMagnetic Locking Area Drive Mode andActuator Display also Remote Status Display Battery Saver FeatureDrive Program Select Key TochangethedrivemodeprogramSleep Mode If Enabled Fault CodesTo charge the batteries by using the onboard charger B a T T E R I E S a N D C H a R G I N GBatteries and Charging Charging Your BatteriesBattery BREAK-IN Can I use a different battery charger?How often must I charge the batteries? Daily UseWhat type of battery should I use? Battery SpecificationsWhy do my new batteries seem weak? How can I get maximum range or distance per charge?How can I ensure maximum battery life? How should I store my Jazzy 1113 and batteries?What about public transportation? What about shipping?Routine Maintenance TemperatureA R E a N D M a I N T E N a N C E Should your Jazzy 1113 come in contact with waterWeekly Checks Daily ChecksTo check the brakes Cleaning Precautions To calibrate the joystick Remote Plus onlyMonthly Checks Yearly ChecksTires and Tubes Drive WheelBattery Replacement To replace the batteriesMotor Brushes Corrective MaintenanceTo inspect or replace the motor brushes O P T I O N a L a C C E S S O R I E S SWING-AWAY Joystick Bracket Elevating LEG RestsSWING-AWAY Foot Rests Specialty Seating SystemsI . W a R R a N T Y Warranty Exclusions Damage caused byT E S T E S US Jazzy 1113/Rev I/Feb03 Quality Control-Model Pride keeps a more detailed report on file at the factory