Pride Mobility Jazzy 1113 To install the battery well frame, To install the battery cases

Page 29

V I I . A S S E M B L Y

To install the battery well frame:

1.Face the rear of the chair and hold the battery well frame so that the “belly” of the well hangs downward.

2.Position the notches on the front of the battery well frame onto the locating pins on the bottom bar of the front frame. See figure 21.

3.Fit the notch on either side of the rear of the battery well frame onto the locating pin on the right frame assembly and onto the locating pin on the left frame assembly.

4.Make certain that the locking mechanisms snap securely into place.

To install the battery cases:

1.Place the front battery case (with the battery inside) into the front end of the battery well frame.

Note: Make certain that the connectors are facing toward the center.

2.Place the rear battery case (with the batteryinside) into the back end of the battery well frame.

3.Make certain that none of the wiring harnesses or cables are pinched between the battery or the motor controller box and the frame.

4.Connect the 4-conductor power cable connectors from the front and rear battery cases to the electronics tray. Push the connector firmly and fully into the socket. See figure 22.

5.Reconnect the left and right motor connectors to their sockets located on the left and right frame assemblies. Be certain to match the left connector to the left motor and the right connector to the right motor (the connectors are labeled left and right).

To install the seat:

1.Pick up the seat by the frame itself (not by the armrests) and slide the locating pins near the back of the frame into the matching slots on the left and rear seat post tower mounts.

2.Slide the pins to the back of the slots. It may be necessary to wiggle the seat slightly from side to side to seat the pins firmly at the back of the slots.

3.Push the front of the seat frame down until both the left and the right frame sides lock into the front seat post tower mounts. See figures 23 and 24.

Figure 20. Fitting the Frames

LOCATING

PINS

Figure 21. The Locating Pins

CONNECTORS

Figure 22. Rear Electronics Tray

US Jazzy 1113/Rev I/Feb03

www.pridemobility.com

29

Image 29
Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Information Exchange N T R O D U C T I O NIntroduction My Authorized Pride Provider Is Pride Owners ClubModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Cornering Information Braking InformationStationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Doors Public Streets and Roadways Stairs and EscalatorsElevators EMI & RFIPositioning Belts Motor Vehicle TransportTransfers Batteries Inclement Weather Precautions Reaching and BendingRemovable Parts AlcoholWhere do radio waves come from? EMI/RFI-FREQUENTLY Asked Questions FaqsAre all power chairs susceptible to EMI? What is the FDA doing about the problem?What should I do if my power chair moves unexpectedly? Jazzy T H E J a Z Z Y 1 1 1Specifications Power Base Back View Power Base Assembly To engage or disengage the drive motors Manual Freewheel LeversTo disassemble the Jazzy I S a S S E M B L YTo remove the footrest To remove the battery well frameTo disconnect the controller To remove the seatTo disassemble the left frame assembly from the front frame To disassemble the right frame assembly from the front frameArmrest Width C O M F O R T a D J U S T M E N T SSeat Height and Angle Controller Extension Armrest AngleArmrest Height Optional Footrest Angle Controller PositionFootrest Height ANTI-TIP Wheels Anti-Tip Wheel AdjustmentTo adjust the anti-tip wheels Frame Assemblies I . a S S E M B L YTo install the seat To install the battery well frameTo install the battery cases To connect the controller Versa Seat or Versa Tilt OptionTo mount the footrest VSI Controller I I . O P E R a T I O NJoystick KeypadSpeed/Profile Keys Battery Condition MeterOn/Off Key Pin Charger Inhibit Connector Controller ConnectorActuator Key and Actuator Lights for optional equipment Horn KeyVSI Error Codes TroubleshootingRemote Plus Master Remote Remote Plus ControllerSpeed Setting Indicator Mode KeyPower Accessory Indicator Right/Left Turn Indicator KeysPower Accessories Speed SettingsOff-board Charger Socket Controller Communications CableSleep Mode Power ModuleActuator Lighting Module Not Shown Trouble CodesEuropa Master Remote Out Of Neutral At Power UpDX Controller Magnetic Locking Area To enable the lockout systemSystem Status Light Battery Saver Feature Drive Mode andActuator Display also Remote Status DisplayDrive Program Select Key TochangethedrivemodeprogramFault Codes Sleep Mode If EnabledB a T T E R I E S a N D C H a R G I N G To charge the batteries by using the onboard chargerBatteries and Charging Charging Your BatteriesCan I use a different battery charger? Battery BREAK-INHow often must I charge the batteries? Daily UseBattery Specifications What type of battery should I use?Why do my new batteries seem weak? How can I get maximum range or distance per charge?How should I store my Jazzy 1113 and batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Temperature Routine MaintenanceA R E a N D M a I N T E N a N C E Should your Jazzy 1113 come in contact with waterTo check the brakes Daily ChecksWeekly Checks To calibrate the joystick Remote Plus only Cleaning PrecautionsMonthly Checks Yearly ChecksDrive Wheel Tires and TubesTo replace the batteries Battery ReplacementTo inspect or replace the motor brushes Corrective MaintenanceMotor Brushes O P T I O N a L a C C E S S O R I E S Elevating LEG Rests SWING-AWAY Joystick BracketSWING-AWAY Foot Rests Specialty Seating SystemsI . W a R R a N T Y Damage caused by Warranty ExclusionsT E S T E S US Jazzy 1113/Rev I/Feb03 Pride keeps a more detailed report on file at the factory Quality Control-Model