Pride Mobility SC4001, SC4401 manual I I . B a S I C Troubleshooting, Diagnostic Fault Codes

Page 37

V I I I . B A S I C T R O U B L E S H O O T I N G

Any electromechanical device occasionally requires some troubleshooting. However, most of the prob- lems that may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.

DIAGNOSTIC FAULT CODES

The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly and easily. The scooter will either display a diagnostic flash code or emit a beep code in the event one of the conditions listed below develops.

NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been turned off, then turned back on.

FAULT CODE

CONDITION

SOLUTION

 

 

 

(1)

Battery charge is low.

Charge batteries as soon as possible.

 

 

 

(2)

Battery charge is too low.

Charge batteries.

 

 

 

(3)

The scooter's battery voltage is too

Unplug charger and/or turn key off,

 

high to operate the scooter, or the

then back on again. If traveling

 

charger is still connected to the off-

down a slope, reduce scooter speed

 

board charger port.

to the minimum setting.

 

 

 

(4)

Current limit time out.

Turn the scooter off for a few min-

 

 

utes, then turn your scooter back on.

 

 

 

(5)

The manual freewheel lever is in the

Remove the key from the key

 

(forward) freewheel position.

switch, then push the manual free-

 

 

wheel lever to the drive (rearward)

 

 

position and restart your scooter.

 

 

 

(6)

Throttle control lever not at center

Return the throttle control lever to

 

position at start up.

center position, turn scooter off then

 

 

back on.

 

 

 

(7)

Speed pot error.

Call your authorized Pride Provider

 

 

for assistance.

 

 

 

(8)

Motor volts error.

Call your authorized Pride Provider

 

 

for assistance.

 

 

 

(9)

Other internal errors.

Call your authorized Pride Provider

 

 

for assistance.

 

 

 

What if all the systems on my scooter seem to be “dead”?

Make certain that the key is in the “on” position.

Check that the batteries are fully charged.

Push in the main circuit breaker reset button. See III. “Your Scooter.”

Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII. “Disassembly and Assembly.”

Be sure the power down timer feature has not been activated. See V. “Operation.”

Celebrity X

www.pridemobility.com

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Celebrity F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y General Removable Parts PRE-RIDE Safety CheckModifications Tire Inflation Weight LimitationsIncline Information S a F E T Y Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesFreewheel Mode Inclement Weather PrecautionsStairs and Escalators DoorsElevators Battery Disposal and RecyclingLift SYSTEMS/ELEVATION Products BatteriesGetting Onto and OFF of Your Scooter Motor Vehicle TransportReaching and Bending Prescription DRUGS/PHYSICAL Limitations Positioning BeltsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RTo Move Rearward use either of the following To Move Forward use either of the followingAnti-Tip Wheels Rear SectionI . Y O U R To install the safelty flagRear Securement Points Securement PointsB a T T E R I E S a N D C H a R G I N G Reading Your Battery VoltageBatteries and Charging Charging Your BatteriesFollow these easy steps to charge your batteries safely Frequently Asked QuestionsHow does the charger work? Can I use a different charger?What type and size of battery should I use? How can I ensure maximum battery life?How often must I charge the batteries? How can I get maximum range or distance per charge?Battery Harnesses and Battery Cables How do I change a battery in my scooter?What about public transportation? Why do my new batteries seem weak?P E R a T I O N PRE-RIDE Adjustments and ChecksBefore Getting Onto Your Scooter Getting Onto Your ScooterGetting OFF Your Scooter Power Down Timer FeatureSeat Rotation Adjustment Tiller Angle AdjustmentFRONT-TO-BACK Seat Adjustment Armrest Width AdjustmentTo install the mirror see figure Seat Height AdjustmentTo adjust the mirror Mirror PositionTo adjust the positioning belt for operator comfort To install the positioning belt if requiredPositioning Belt Optional To release the positioning beltTo operate the power seat Power Seat AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyAssembly Diagnostic Fault Codes I I . B a S I C TroubleshootingWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Solid Tire Wheel Removal Wheel ReplacementNylon Lock NUT Replacement Wiring HarnessesFuses To replace a fuseDisposal of Your Scooter Storing Your ScooterP E N D I X I Specification S P E N D I X I Specification S T E S T E S Page INFMANU2995
Top Page Image Contents