Pride Mobility SC4001, SC4401 manual C a R E a N D M a I N T E N a N C E

Page 39

I X . C A R E A N D M A I N T E N A N C E

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance.

TIRE PRESSURE

If equipped with pneumatic tires, always maintain the psi/bar/kPa air pressure indicated on each tire.

WARNING! It is important that the psi/bar/kPa air pressure indicated on each tire be maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and overinflated tires may burst. Failure to maintain the psi/bar/kPa air pressure indicated on pneumatic tires at all times may result in tire and/or wheel failure.

Regularly inspect your scooter’s tires for signs of wear.

EXTERIOR SURFACES

Bumpers, tires, and trim can benefit from an occasional application of rubber or vinyl conditioner.

WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tire tread, as this may cause them to become dangerously slippery.

CLEANING AND DISINFECTION

Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter. Avoid using products that may scratch the surface of your scooter.

If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your product before application.

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning agent before applying it to your product. Failure to comply may result in skin irritation or premature deterioration of upholstery and/or scooter finishes.

BATTERY TERMINAL CONNECTIONS

Make certain that the terminal connections remain tight and uncorroded.

The batteries must sit flat in the battery wells.

ABS PLASTIC SHROUDS

The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are coated with an advanced formula urethane paint.

A light application of car wax will help the shrouds retain their high gloss.

MOTOR BRUSHES

The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodi- cally for wear by your authorized Pride Provider.

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY

You do not need to lubricate these items, as they are all prelubricated and sealed.

Celebrity X

www.pridemobility.com

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Celebrity F E T Y G U I D E L I N E S N T E N T S Shipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Removable Parts PRE-RIDE Safety Check GeneralModifications Weight Limitations Tire InflationIncline Information S a F E T Y Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesDoors Inclement Weather PrecautionsFreewheel Mode Stairs and EscalatorsBatteries Battery Disposal and RecyclingElevators Lift SYSTEMS/ELEVATION ProductsMotor Vehicle Transport Getting Onto and OFF of Your ScooterReaching and Bending Positioning Belts Prescription DRUGS/PHYSICAL LimitationsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RTo Move Rearward use either of the following To Move Forward use either of the followingAnti-Tip Wheels Rear SectionI . Y O U R To install the safelty flagRear Securement Points Securement PointsCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different charger? Frequently Asked QuestionsFollow these easy steps to charge your batteries safely How does the charger work?How can I get maximum range or distance per charge? How can I ensure maximum battery life?What type and size of battery should I use? How often must I charge the batteries?Battery Harnesses and Battery Cables How do I change a battery in my scooter?What about public transportation? Why do my new batteries seem weak?Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Before Getting Onto Your ScooterGetting OFF Your Scooter Power Down Timer FeatureArmrest Width Adjustment Tiller Angle AdjustmentSeat Rotation Adjustment FRONT-TO-BACK Seat AdjustmentMirror Position Seat Height AdjustmentTo install the mirror see figure To adjust the mirrorTo release the positioning belt To install the positioning belt if requiredTo adjust the positioning belt for operator comfort Positioning Belt OptionalTo operate the power seat Power Seat AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyAssembly I I . B a S I C Troubleshooting Diagnostic Fault CodesWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Solid Tire Wheel Removal Wheel ReplacementTo replace a fuse Wiring HarnessesNylon Lock NUT Replacement FusesDisposal of Your Scooter Storing Your ScooterP E N D I X I Specification S P E N D I X I Specification S T E S T E S Page INFMANU2995
Top Page Image Contents