Invacare Spectra Plus user manual Tray Assembly Fitting Operation Instructions

Page 29

TRAY ASSEMBLY

FITTING - OPERATION INSTRUCTIONS

IMPORTANT: ENSURE THAT THE JOYSTICK CONTROL UNIT IS SWITCHED OFF BEFORE FITTING, REMOVING OR ADJUSTING THE TRAY ASSEMBLY.

The tray assembly comes ready assembled and is designed to fit to either the left or right hand side of the wheelchair.

The cut-out section is to accommodate the Joystick Control unit and determines which side the tray is fitted i.e. Joystick Control fitted to the right hand side, therefore the tray fixings will be fitted to the left hand side, and vice-versa.

Follow these simple instructions to fit:-

1.Remove the two screws A holding the arm pad to armrest support tube B.

2.Fit the slide mounting tube C beneath the armrest support tube using the existing screws, (see diagram). Tighten the screws securely, (do not over tighten as this will damage the T-nut inserts within the arm pad).

3.Loosen the wing screw D and slide the tray support tube extension into the slide mounting tube C.

4.With the occupant seated in the chair, adjust the tray to a comfortable working position, tighten wing screw D.

5.Side to side lateral adjustment can be achieved by loosening the 4 screws E and sliding the tray surface to the required position.

6.Ensure the tray is firmly positioned, level and central to the occupant’s requirements.

OPERATION - REMOVAL (Switch OFF the Controller)

The Tray can be placed to the side or removed completely to allow the occupant to get in and out of the chair safely.

To do this, loosen the wing screw D, lift the tray and place to the side of the chair or remove completely by pulling the tray assembly forward.

Do not attempt to drive the chair with the tray placed to the side as this may be hazardous to the occupant and other people.

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Spectra Plus Contents Foreword Purpose of the Power ChairAdvisory Safety Notice Safety Precautions Getting Acquainted with Your NEW Power ChairJoystick FeaturesBackrest Angle Adjustment Seat and Backrest AdjustmentSeat Depth Adjustment 35mm depth adjustment Armrest Adjustment MANUALALTILTT--IN--SPACE TensiontensionadjustableadjustablebackrestPilot Integral Handling and Operation ControllersRecommended Driving Position Dynamic DL ControllerDX-REMG80IMASTER Remote Important Information for Your Safety IntroductionHandling and Transportation Driving the WheelchairSafety and Misuse Warnings MaintenanceFault Diagnostics Left and Right Indicators Controlling Lighting Functions Using the KeypadAppendix a Side LightsNegotiating Kerbs PILOT+Negotiating GRADIENTS/SLOPES Controls Joystick Module DetailsHorn Switch Maximum Speed Indicator Speed Adjustment Mode DUAL/ATTENDANT Control Controller OptionsCircuit Breakers 30 AMP Chin Control Attendant ControlTransfers Footrests AdjustmentLowest Part Footrest Must be AT Least For Clearance Elevating LegrestsLevers Pointing Rearwards Pushing the Chair Freewheel ModeOperating the Chair Outdoors Kerb Climbing RE-ASSEMBLYGoing UP a Kerb Going Down a KerbDIS-ASSEMBLY Detachable Motors Drive WHEEL-LOCKS Manual Brakes Drive Wheel RemovalOccupant’s inertia seat belt Which also must be used Power chair was ttestted toLabelled „TIIEDOWNPOINTPOINT Diiagram Fig. No..2 shows Fig. No.3 TransportationOperation Removal Switch OFF the Controller Tray Assembly Fitting Operation InstructionsShown in Fig Lateral Support Fitting InstructionsMains Socket Charger Controller Front Charging BatteriesBatteries Pollution from improper disposal Battery ConnectionsCHROME/PAINTWORK Keeping Your Chair in Good ConditionFault Finding Daily Weekly Monthly Yearly Spectra PlusTechnical Information Approved Accessories Available Models Covered Spectra Plus Spectra Plus
Top Page Image Contents