Omega Engineering #M3350/0101 manual Logging In to CN8-SW Using the Default Account, To log

Page 25

CN8-SW™UserÕs Guide

3.3Logging In to CN8-SW Using the Default Account

When you start the CN8-SW application, the Operator Login Window will be displayed.

By default, newly installed CN8-SW software will be set up to recognize one login account. This is user ÒMULTIÓ. The password is ÒCOMMÓ.

To log in:

1.Start the CN8-SW application.

2.Select File Login. The Operator Login window will be displayed.

3.Click on the User Id text entry box and type in MULTI. CN8-SW user names and passwords are case-sensitive. This means that capitalization matters. To the software ÒMULTIÓ, ÒmultiÓ, and ÒMultiÓ are all different names.

4.Tab to the Password entry box or click on it. Type in COMM.

5.Click on OK. The CN8-SW window will open. Because the software was newly installed, the main display will be blank. In the future, once communication has been established with controllers, and the controller identities saved as a CN8-SW system file, logging in will result in the display of the controllers in the most recently used

.MCS file.

3-4

Image 25

Contents CN8-SW Table of Contents Viewing and Changing Controller Configuration Parameters Changing Controller Mode and Using AutotuneConfiguring and Running Ramp and Soak Recipes CN8-SWUserÕs Guide11-1 Table of ContentsCN8-SWUserÕs Guide Transforms a PC into an Operator Station FeaturesGraphical Interface Automated Ramp and Soak Cycles Storing and Loading Configuration Parameter SetsLogging IntroductionHardware and Software Requirements Local Alarms1 CN8-SW Computer ControllersStep Task Section This Manual Overview of Setup TasksCN8-SWUserÕs Guide Step Task Section in this Manual Availability of Functions Overview of CN8-SW MenusFile Menu Function Purpose SectionView Menu Edit MenuController Menu Alarms Ramp/Soak Menu Options MenuHelp Menu Menu Convention Used in This Manual General Instructions for Using CN8-SW WindowsCN8-SWUserÕs Guide Introduction Wiring the Network and Connecting the ComputerIntroduction Connecting Controllers and the Computer to the Network2 RS-232 Interface 3 RS-485 Network Wiring the Network and Connecting the ComputerCN8-SWUserÕs Guide Installing the Software Installing the Software and LoggingTo install the software CN8-SWUserÕs Guide Starting the Software Installing the Software and LoggingTo log Logging In to CN8-SW Using the Default AccountTo change the password Changing the Password for the Default AccountPermissions Available Setting Up Operator AccountsTo see the permissions available to a user account To add an operator login account ProcedureDeleting an Operator Account Editing an Operator AccountLogging Out of the CN8-SW Application Establishing Communication with Controllers Communication Parameters Establishing Communication with Controllers Network AddressesTo configure the CN8-SW communication settings Configuring Communication Parameters for CN8-SW SystemEstablishing Communication with Controllers Recognizing Controllers with the CN8-SW Software Automatically Using the Find Controllers OptionTo use the automatic function If any controllers were not recognized Page To add a controller manually Manually Using the Controller MenuTo delete a controller Deleting a ControllerChanging Baud Rate after Communication Has Been Established Establishing Communication with Controllers Saving the .MCS File Naming ControllersClosing an .MCS File Creating a New .MCS FileOpening an Existing .MCS File CN8-SWUserÕs Guide Procedure Configuring Local AlarmsCN8-SWUserÕs Guide Viewing Process Values and Changing Setpoint Viewing PV and SP in the Main Window To view the real-time trend graph Viewing PV and SP in a GraphTo change a controllerÕs setpoint Changing the Setpoint Using the Setpoint Dialog BoxSetpoint Configuring and Invoking the Single-Step Ramp Function CN8-SWUserÕs Guide To invoke the single step ramp function To change a controllerÕs mode Changing Controller Mode and Using AutotuneCN8-SWUserÕs Guide Accessing Configuration Parameter Displays Viewing and Changing Controller Configuration ParametersUsing Configuration Parameter Displays To access the parameter displaysCN8-SWUserÕs Guide Configuring and Running Ramp and Soak Recipes Creating a New Recipe Configuring CN8-SW RecipesConfiguring and Running Ramp and Soak Recipes Editing an Existing Recipe Starting to Run a Recipe Running CN8-SW RecipesTo run a CN8-SW Ramp/Soak recipe To hold execution of a CN8-SW recipe Holding Pausing Recipe ExecutionTo resume execution of a ÒheldÓ recipe Resuming Recipe ExecutionTo stop execution of a CN8-SW recipe Stopping Recipe ExecutionConfiguring Controller Ramp and Soak Parameters CN8-SWUserÕs Guide Configuring and Running Ramp and Soak Recipes Running Controller Ramp and Soak Cycles Storing and Loading Controller Configurations Storing Configuration Storing and Loading Controller Configurations Loading Configuration Storing and Loading Controller Configurations 10-6 To turn on the logging function Turning On the Logging FunctionTurning Off the Logging Function Viewing and Printing Log FilesTo turn off the logging function Index 12-2