Panasonic AWHE50HN, AWHE50SN manual Preset memories, Position may occur

Page 19

Preset memories

This unit enables up to 100 settings for the camera direction (panning and tilting), zoom, focus, iris, gain and white balance to be registered in its preset memories, and called. However, the number of settings that can be registered and called depends on the type of wireless remote control or controller that is used for operation.

ppThe operating mode (manual or auto setting) is not registered for the focus and iris settings.

The current focus and iris values are registered.

ppThe focus and iris values can be recalled only when the manual settings are applicable.

ppAWB A, AWB B or ATW is registered as the white balance setting. The values selected when AWB was

established are recalled as the adjustment values of AWB A or AWB B.

ppThe AWB Mode (ATW, AWB A or AWB B) stored using the AW‑RP655 are recalled only when the AW‑RP655 is connected.

Notes

ppWhen there is a large difference in the environmental temperature between the time of registration and the time the setting is called, displacement of the preset

position may occur.

ppIf displacement occurs, perform registration again. pp While preset settings are being called, it is not

possible to perform manual operations such as panning, tilting, zooming or iris adjustments.

pp If, when one set of preset settings has been called, another set of preset settings is then called, the first set of preset settings which have been called will take precedence.

When performing the operations using the wireless remote control

Twelve settings (preset No.1 to No.12) can be registered and called using the wireless remote control.

The [1] to [12] buttons correspond to the unit’s preset memories No.1 to No.12.

qqRegistering the settings in the preset memories

1Display the picture to be shot on the monitor.

Operate the pan, tilt or zoom buttons to determine the camera angle.

Adjust the focus, iris, gain and white balance if they need to be adjusted.

2While holding down the [PRESET] button, press the button corresponding to the preset memory number.

ppIf a preset memory number with an already registered setting has been selected, the existing setting will be erased and replaced with the new one.

qqCalling the settings of the preset memories

1Press the button in which the preset memory setting has been registered.

19

Image 19

Contents AW‑HE50SN Contents WwOverview Before useWwConcerning the Operating Instructions WwTrademarks and registered trademarks WwRequired personal computer environmentWwAbout copyright and licence WwNetwork security WwDisclaimer of warrantyBasic shooting operations Select the shooting modeWhen the AW‑RP50 is connected How to turn the power on and offWwTurning the power on Set the Operate switch on the controller to onSet the Operate switch on the controller to OFF WwTurning the power offSelecting the shooting modes scene files Selecting the unitsWwTypes of shooting modes WwHow to select the shooting mode Press the OK button again Press the Menu buttonTurn the jog dial main Press the OK buttonQqChanging the camera’s direction QqUsing the zoom functionQqSwitching the direction or zoom speed ShootingMenu screen is displayed Lens focus is not adjusted automaticallyUnit does not move Multiple color bands color bars are displayedMore advanced operations Manual shooting WwManually adjusting the focus WwManually adjusting the iris Press the Shutter button and turn its lamp on WwManually adjusting the shutter speedPress the OFF, LOW or HI button WwManually adjusting the gainPress the Gain button to turn off its lamp Position may occur Preset memoriesHold down the Memory button Set to the memory recording modeSet the memory recording mode Hold down the Reset buttonWhen the AW‑RP555 is connected WwWhite balance adjustment White balance adjustmentQqAutomatic adjustment AWB AWB A or AWB B Press the AWC button Press the SET button for 2 secondsQqAuto tracking white adjustment ATW Press the IRIS - button Black level master pedestal adjustmentWwBlack level master pedestal adjustment Press the M/IRIS buttonPress the Iris button several times to turn off its lamp WwGenlock adjustment Genlock adjustment AW‑HE50S onlyQqHorizontal phase adjustment Press the Mode button QqColor phase adjustmentGenlock adjustment AW‑HE50S only Table of operations Basic operationsChanging Press the  or  button to change the setting Jog dial R Jog dial mainPress the Menu button for 2 seconds to exit the camera menu QqProcedure for camera menu operation AW‑RP655Mode button lights up at the BAR setting Press the Item button QqProcedure for camera menu operation AW‑RP555Press the Menu button of the AW‑RP555 for 2 seconds Perform one of the following steps to select the menu itemCamera OSD QqProcedure for camera menu operation AW‑RP50WwSetting the menu items Setting the menu itemsWwTop Menu WwCamera screen When Manual1 to 3 is selected WwCamera screen When FullAuto is selectedWwContrast screen WwPicture 1/2 screen WwSystem screen WwPicture 2/2 screenWwOutput screen WwGenlock screen AW‑HE50S onlyRGB-NOR Format unchanged screen QqChanging the formatFormat change check screen Format Set screenWwOther 1/2 screen OSD Off With Tally Off, On Tally Enable Disable, EnableWireless Control Disable, Enable WwOther 2/2 screenWwFirmware Version screen WwMaintenance screenInitialize screen Menu settings initialized screenMenu settings unchanged screen QqConcerning initializationMenu item table Menu Factory setting Selection items FullAutoWeb setting screen WwMenu operations Control Setup Power on button / Standby button  Control button / Setup button Zoom  Focus WwControl screen Control pad and its buttons  Preset Brightness QqBasic screen WwSetup screen Basic button Preset position Image  Image Image adjustQqImage screen Image adjust screen  Scene FullAuto, Manual1, Manual2, Manual3  Contrast Contrast Mode Auto, ManualAWB  Picture Chroma Level -3 to +3Preset position setting screen  Preset  Zoom  Limitation Setting  Genlock AW‑HE50S only  Output ENH setting instead Other QqUser mng  IP address Host auth. screen  Host auth Host check QqServer Network screen  IP network QqNetworkIP address Subnet mask Default gatewayPort numbers already used 20, 21, 23, 25, 42, 53, 67, 68  Host name 1 to 64 half-size characters  Password 0 to 32 half-size characters Access interval Ddns screen Contact 0 to 255 half-size characters Snmp screen Community 0 to 32 half-size characters  Location 0 to 32 half-size characters Time & date QqMaintenance Error description System log screenUpgrade screen Enter the software version in the xxxxx part  Reset to the default and load the default Html files Default reset screen Reset to the default Except the network settings  Load the default Html files setup menu Download Back up screen Upload Other screen Category Display Description of error DDNS-related error displaysNTP-related error displays Login-related displaysLimiters Press one of the CAM1 to CAM4 buttons to select the unit Setting/releasing the limitersWwSetting the limiters WwBasic limiter operationsPp Releasing the lower limit position of the movement range WwResetting the limitersWwReleasing the limiters Pp Releasing the upper limit position of the movement rangeWwConcerning the safe mode Safe modeTrouble-triggered safe mode CPU WwSystem requirements for a PCSymptom WwPrecautions when using Windows VistaSolution Symptom QqRestrictions Restriction When activating audio on the web browserWwPrecautions when using Windows Restriction 2 When using Windows 7 with some products Restriction 1 On the setup pages for some productsPanasonic Solutions Company

Related manuals

Manual 90 pages 45.33 Kb