Panasonic AWHE50HN, AWHE50SN manual  Other, Install Position Desktop, Hanging

Page 65

Web setting screen

Other

This item’s setting is reflected when the Set button is pressed.

Install Position [Desktop, Hanging]

“Desktop” or “Hanging” is selected here as the method used to install the unit.

Desktop

Stand-alone installation

 

 

Hanging

Suspended installation

 

 

When “Hanging” has been selected, the top, bottom, left and right of the images will be reversed, and up/down/left/right control for panning and tilting will also be reversed.

Preset Speed [1 to 30]

There are 30 preset pan-tilt operation speeds of when regenerating the camera direction and other information which are registered in the preset memory.

Notes

ppIf a high value is selected for the Preset Speed setting, the image on the screen may shake when

operation stops.

ppWhen connecting the unit to the AW‑RP655 for use, the “DIAGONAL SPEED (P/T SETTING)” setting of the AW‑RP655 takes effect.

To change the Preset Speed, change the AW‑RP655 setting.

Preset Scope [Mode A, Mode B, Mode C]

Selected here are the setting items to be recalled when the contents of the preset memory are regenerated.

Mode A

Pan, Tilt, Zoom (including digital zoom),

 

Focus, Iris, Gain, White-BAL

 

 

Mode B

Pan, Tilt, Zoom (including digital zoom),

 

Focus, Iris

 

 

Mode C

Pan, Tilt, Zoom (including digital zoom),

 

Focus

 

 

Digital Zoom [Disable, Enable]

“Enable” or “Disable” is set here for the digital zoom function.

If zooming is performed toward the Tele end beyond the maximum position when “Enable” has been selected, the digital zoom can be operated continuously. Zooming will stop temporarily at the position where the optical zoom and digital zoom are switched so after it has stopped at this position, proceed with zooming again.

When the setting is changed to “Disable” while already in the digital zoom region, the zoom will automatically move to the maximum position of the optical zoom.

Speed With Zoom POS. [Off, On]

“On” or “Off” is set here for the function used to adjust the camera direction’s adjustment speed in conjunction with the zoom magnification.

When “On” is set, the panning and tilting operations will become slower in the zoom status.

This function has no effect during preset operations.

Focus Mode [Auto, Manual]

“Auto” or “Manual” is set here for the focusing function.

Auto

The subjects are always brought into focus

 

automatically.

 

 

Manual

The focus is operated manually.

 

 

Focus ADJ With PTZ. [Off, On]

“On” or “Off” is set here for the function which compensates for out-of-focusing when it occurs during panning, tilting or zooming operations at the manual focus setting.

When “Off” is set, adjust the focus as required after zooming or set the focus to the auto mode. This item can be selected only when “Manual” has been selected as the “Focus Mode” setting.

Tally Enable [Disable, Enable]

“Enable” or “Disable” is set here for the function which turns on or turns off the tally lamp using the tally control signal.

OSD Status [Off, On]

“On” or “Off” is set here for the status display which appears during AWB operations.

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents AW‑HE50SN Contents WwConcerning the Operating Instructions Before useWwOverview WwAbout copyright and licence WwRequired personal computer environmentWwTrademarks and registered trademarks WwNetwork security WwDisclaimer of warrantyBasic shooting operations Select the shooting modeWwTurning the power on How to turn the power on and offSet the Operate switch on the controller to on When the AW‑RP50 is connectedSet the Operate switch on the controller to OFF WwTurning the power offWwTypes of shooting modes Selecting the unitsSelecting the shooting modes scene files WwHow to select the shooting mode Turn the jog dial main Press the Menu buttonPress the OK button Press the OK button againQqSwitching the direction or zoom speed QqUsing the zoom functionShooting QqChanging the camera’s directionUnit does not move Lens focus is not adjusted automaticallyMultiple color bands color bars are displayed Menu screen is displayedMore advanced operations Manual shooting WwManually adjusting the focusWwManually adjusting the iris Press the Shutter button and turn its lamp on WwManually adjusting the shutter speedPress the Gain button to turn off its lamp WwManually adjusting the gainPress the OFF, LOW or HI button Position may occur Preset memoriesSet the memory recording mode Set to the memory recording modeHold down the Reset button Hold down the Memory buttonWhen the AW‑RP555 is connected QqAutomatic adjustment AWB AWB A or AWB B White balance adjustmentWwWhite balance adjustment Press the AWC button Press the SET button for 2 secondsQqAuto tracking white adjustment ATW WwBlack level master pedestal adjustment Black level master pedestal adjustmentPress the M/IRIS button Press the IRIS - buttonPress the Iris button several times to turn off its lamp QqHorizontal phase adjustment Genlock adjustment AW‑HE50S onlyWwGenlock adjustment Press the Mode button QqColor phase adjustmentGenlock adjustment AW‑HE50S only Table of operations Basic operationsChanging Press the  or  button to change the setting Jog dial R Jog dial mainPress the Menu button for 2 seconds to exit the camera menu QqProcedure for camera menu operation AW‑RP655Mode button lights up at the BAR setting Press the Menu button of the AW‑RP555 for 2 seconds QqProcedure for camera menu operation AW‑RP555Perform one of the following steps to select the menu item Press the Item buttonCamera OSD QqProcedure for camera menu operation AW‑RP50WwTop Menu Setting the menu itemsWwSetting the menu items WwCamera screen When Manual1 to 3 is selected WwCamera screen When FullAuto is selectedWwContrast screen WwPicture 1/2 screen WwSystem screen WwPicture 2/2 screenWwOutput screen WwGenlock screen AW‑HE50S onlyRGB-NOR Format change check screen QqChanging the formatFormat Set screen Format unchanged screenWwOther 1/2 screen Wireless Control Disable, Enable Tally Enable Disable, EnableWwOther 2/2 screen OSD Off With Tally Off, OnWwFirmware Version screen WwMaintenance screenMenu settings unchanged screen Menu settings initialized screenQqConcerning initialization Initialize screenMenu item table Menu Factory setting Selection items FullAutoWeb setting screen WwMenu operations Control Setup Power on button / Standby button  Control button / Setup button Zoom  Focus WwControl screen Brightness  Preset Control pad and its buttons  Basic button WwSetup screenQqBasic screen QqImage screen Image  Image Image adjustPreset position Image adjust screen  Scene FullAuto, Manual1, Manual2, Manual3  Contrast Contrast Mode Auto, ManualAWB  Picture Chroma Level -3 to +3Preset position setting screen  Preset  Zoom  Limitation Setting  Genlock AW‑HE50S only  Output ENH setting instead Other QqUser mng  Host check Host auth. screen  Host auth IP address QqServer IP address QqNetworkNetwork screen  IP network Port numbers already used 20, 21, 23, 25, 42, 53, 67, 68 Default gatewaySubnet mask  Access interval  Password 0 to 32 half-size charactersDdns screen  Host name 1 to 64 half-size characters Community 0 to 32 half-size characters Snmp screen Location 0 to 32 half-size characters  Contact 0 to 255 half-size characters Error description QqMaintenanceSystem log screen  Time & dateUpgrade screen Enter the software version in the xxxxx part  Reset to the default Except the network settings Default reset screen Load the default Html files setup menu  Reset to the default and load the default Html files Upload Back up screen Download Other screen NTP-related error displays DDNS-related error displaysLogin-related displays Category Display Description of errorLimiters WwSetting the limiters Setting/releasing the limitersWwBasic limiter operations Press one of the CAM1 to CAM4 buttons to select the unitWwReleasing the limiters WwResetting the limitersPp Releasing the upper limit position of the movement range Pp Releasing the lower limit position of the movement rangeTrouble-triggered safe mode Safe modeWwConcerning the safe mode CPU WwSystem requirements for a PCSolution WwPrecautions when using Windows VistaSymptom Symptom QqRestrictions Restriction When activating audio on the web browserWwPrecautions when using Windows Restriction 2 When using Windows 7 with some products Restriction 1 On the setup pages for some productsPanasonic Solutions Company
Related manuals
Manual 90 pages 45.33 Kb
Top Page Image Contents