IBM M/02-212 III.2.2 AC-Adaptor, III.2.3 Printer Connection, III.2.4 Computer Connection

Page 11

III.2.2 AC-Adaptor

The AC adaptor supplies R/S Rheometer with power.

Only the AC-adaptor delivered by BROOKFIELD with your Rheometer may be used for power supply of R/S Rheometer.

The AC-adaptor may be inserted to the socket with corresponding grounding only. Connect the AC adaptor only using the plug in a proper way grounded to avoid electric shocks or damage of the system components. Pay attention also to “Requirements to the mains cable” (see Appendix).

Connecting the AC-adaptor:

-be sure that R/S Rheometer is switched off (mains switch “POWER” at the back side of the instrument);

-insert the instrument connector of the mains cable into AC adaptor;

-insert the plug of DC cable into the connector “DC” at the back side of R/S Rheometer;

-insert the mains plug of the mains cable into a grounded socket;

-turn on the R/S Rheometer again.

The AC-adaptor should not remain connected to the mains socket during long time with disconnected plug of the DC cable from the connector “DC” at the back side.

Before disconnecting R/S Rheometer from mains supply be sure that the Rheometer is switched off.

III.2.3 Printer Connection

Printer can be connected directly to the interface connector of the R/S Rheometer when measuring without PC support. You must preset “Printer” as output device to print the measuring values during measurement (see Chapter 6).

You should use obligatory a printer with parallel “CENTRONICS” interface.

-Turn off the R/S Rheometer with the mains switch “POWER” at the back side.

-Insert the printer connecting cable into the connector “CENTRONICS” at the back side of rheometer.

-Turn on R/S Rheometer again.

Standard printer cable (Printer ↔ PC) can be used as printer connecting cable. This cable is supplied with the printer in most cases.

To print data-values from R/S Rheometer all printers can be used which are printing text in ASCII-mode.

III.2.4 Computer Connection

If the R/S Rheometer has to be used in “REMOTE” mode with PC support (Rheo-program package) or with serial data-terminal for data logging it is necessary to connect the data link with the plug “RS232” at the instrument back side.

-Turn off the R/S Rheometer with the mains switch “POWER” at the back side.

-Turn off your computer system.

-Insert the data link into the plug “RS232” at the back side of the rheometer.

-Connect the other end of the data link with a free serial interface RS-232 (f.e. “COM2”) of your computer.

-Turn on the R/S Rheometer and your computer system again.

Use data link cable of BROOKFIELD delivery only!

Brookfield Engineering Labs., Inc.

Page 11

M/02-212

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Brookfield R/S Rheometer Brookfield Engineering Labs., Inc 02-212 Contents Appendix Measuring Principle General DescriptionUse of the Rheometer II.1 R/S Rheometer II. System ConfigurationRheometer main instrument minimum configuration II.3 Computer System II.2 Measuring DevicesIII.1 Stand Mounting III. Instrument InstallationHints for height adjustment of the stand III.2 Electrical Connections III.2.1 Temperature Sensor Pt100Use data link cable of Brookfield delivery only III.2.2 AC-AdaptorIII.2.3 Printer Connection III.2.4 Computer ConnectionFTK-CC III.3 Mounting of temperature controlled measuring devicesThermostat connection to temperature control device FTK-CC III.3.2 Mounting of the measuring device ME-CP/PP Thermostat connection to temperature control device FTK-CCBrookfield Engineering Labs., Inc 02-212 Brookfield Engineering Labs., Inc 02-212 Mounting III.3.3 Mounting of the cooling device KEIV.2 Handling IV. Environment, handling, cleaning and maintenanceIV.3 Cleaning IV.1 Operating environment, StorageIV.4 Maintenance Measurement directly in the substance Measuring SystemsDepth of immersion Measurement with substance in measuring systemMeasurement with temperature control device FTK-CC Turn left Turn right Lower Lift Brookfield Engineering Labs., Inc 02-212 Voltage check VCC15.25 VI. Operation and Menue SystemRheometer Ver .02 #xxxxxx 07.05.98 Brookfield Brookfield VI.1 KeyboardKey-function dependent to executed operation Print programs from memory VI.2 Menu System of R/S RheometerZero-point calibration Define/edit programMain-menue Run Single Run Program Remote CONFIGURATION-,emie Set time/date Set RS232 Param LanguageMenu handling VI.3 Selecting from ListsInput Values Val.1/s0200.00 Nr. of MP010 Times0100 VI.4 Input of numerical values and alphanumeric textsSelect Measuring system CC48 CC45 Input Values Val.1/s0100.00 Nr. of MP010 TimesInput Values Val.1/s0290.00 Nr. of MP Times0100 Input Values Val.1/s0200.00 Nr. of MP Times0100VI.5.1 MAIN-Menue → Run Single VI.5 Menue entries Main menueProg. Running Wait for 1.MP Output of MPs to No output device Memory Menu ST StartSelect program Prog xyz Test Prog Öl Program end Single mode Total time100s Total #MP10VI.5.2 MAIN-Menue → Run Program No valid program Enter program firstProg. running Wait for 1.MP #1 Output of MPs to Printer Memory MenueProgram end Test Total time200s Total #MP40 VI.5.5 Main menue → ConfigurationVI.5.3 Main menue → Remote VI.5.4 Main menue → UtilitiesVI.6.2 Utilities → Edit Programs VI.6 Menue entries in the Utilities-MenueVI.6.1 Utilities → Zero Calibration D1/s=ft Select Input-Mode -D1/s Nrpm TauPa Select Prog to edit Prog xyz Test NEWSelect Meas. system CC45 CC25 CC14 Nr. of stepsEdit Program name Range-Error Range-Error Start-Value min 0.90 maxInput Step Nr time s Printer not ready OK cont. ST stop VI.6.3 Utilities → Print ProgramsVI.6.4 Utilities → Measuring systems Test Press OK to saveSel. Output-device Printer RS232 VI.6.5 Utilities → Print memoryEnter Meas. Sys. #4 Name CP25 tauprom 01.1418 kgamma Press OK to save Name CC25 tauprom 01.1418 kgammaVI.6.6 Utilities → Clear memory VI.6.7 Utilities → Measure temperatureSelect output device No output device Printer RS232 VI.7 Menu entries of the Configuration menuVI.7.1 Configuration → Set output mode Service, Service2 for service personnel onlyVI.7.4 Configuration → Set Time/Date VI.7.2 Configuration → MeasCount modeVI.7.3 Configuration → Reset meascount RS232 4800,8,n,1 Change RS232-Par.? Okyes Stno VI.7.5 Configuration → Set RS232 ParameterNew Time/Date 1715 Press OK to save Baudrate -4800 9600 VI.7.6 Configuration → LanguageVI.7.7 Configuration → Service, Service VI.8 Serial Data transfer via Interface RS232Brookfield Engineering Labs., Inc 02-212 Brookfield Engineering Labs., Inc 02-212 Measurement with FTK-CC VII.1 Measuring in manual modeVII. Measurements Measurement controlVII.2 Measuring in Remote-mode Measurement in remote control modeVIII. Technical data Measured or evaluated values Weight Temperature rangeIX. Guarantee Given ranges are standard values not maximum values A1Data sheets of standard measuring systemsDG DIN Table Plate/Plate measuring systems DIN Measuring system C25-1 C25-2 C50-1 C50-2 C75-1 C75-2Range error End value min 0.90 max A2 Error messagesRange Error Printer ErrorBreak torque max! Single mode Total MP Total time Zero Calibration ErrorError #3 Zero cal. error Please retry cal ST stop Break Speed MAX Break Speed max! Single mode Total MP Total timePC Side A3 Pin-layout of the serial data cableRheometer side Other countries A4 Requirements to the mains connecting cablesGeneral information USA and CanadaEnglishGermanEnglishGerman A5 Language cross referenceGerman menue system of RC20 Index

M/02-212 specifications

The IBM M/02-212 is a cutting-edge platform that showcases the company’s dedication to excellence in technology and innovation. Designed for both enterprise performance and flexibility, this model adheres to IBM's high standards for processing power and reliability, making it a standout option for businesses looking to enhance their operations.

One of the main features of the M/02-212 is its powerful multi-core processor, which provides exceptional speed and efficiency. This architecture enables the system to handle multiple tasks simultaneously without compromising performance, making it ideal for data-intensive applications and complex processing tasks. It supports a range of workloads, from traditional enterprise applications to modern cloud-based solutions.

In terms of memory, the M/02-212 offers extensive capacity options, utilizing high-speed RAM technology that ensures swift data access and reduced latency. The combination of powerful processing and ample memory resources allows organizations to execute demanding applications and large-scale databases seamlessly.

The system is designed with advanced security features that are integral for protecting sensitive information. Encryption capabilities, secure boot options, and comprehensive identity management functionalities are built-in, providing a robust defense against potential cyber threats. This is particularly valuable for industries like finance and healthcare, where data integrity is paramount.

Moreover, the IBM M/02-212 leverages state-of-the-art virtualization technologies, enabling companies to optimize resource utilization and increase operational efficiency. Through virtualization, multiple virtual machines can run on a single physical server, allowing businesses to reduce hardware costs and improve overall system management.

The M/02-212 also emphasizes scalability, which means organizations can easily expand their capabilities as their needs evolve. This flexibility allows businesses to adapt to changing market conditions without requiring a complete overhaul of their existing infrastructure.

Additionally, it comes equipped with a user-friendly management interface, providing administrators with the tools necessary to monitor system performance, allocate resources, and troubleshoot issues efficiently.

In summary, the IBM M/02-212 combines powerful processing capabilities, robust security measures, advanced virtualization, and exceptional scalability. These characteristics make it an excellent choice for enterprises looking to enhance their IT infrastructure while ensuring efficiency and data security.
Top Page Image Contents