Deltech Fitness LS60, LS2580 instruction manual Shutdown and Depressurize Dryer. Refer to the Purge

Page 57

PROBLEM/POSSIBLE CAUSE

CHECKS AND REMEDY

Back pressure on a desiccant chamber during the regeneration cycle. (Chamber’s pressure gauge indicates above zero (0) PSIG.

Note: The presence of back pressure will result in insufficient regeneration followed by dew point degradation. An off-stream chamber’s pressure gauge MUST indicate zero (0) PSIG throughout all regeneration cycles.

1.

Purge Adjusting Valve is supplying excessive

1.

SLOWLY rotate Purge Adjusting Valve until correct purge pres-

 

purge gas to regenerating chamber as indi-

 

sure setting is noted on the Purge Pressure Indicator.

 

cated by the Purge Pressure Indicator

 

Note: The purge pressure setting can only be read and ad-

 

(gauge).

 

 

 

justed when the off-stream chamber has depressurized for re-

 

 

 

 

Note: If correct setting is unknown, refer to

 

generation. When the off-stream chamber is pressurized the

 

the Calculation of Purge Pressure Setting in-

 

Purge Pressure Indicator will read system pressure.

 

structions in Appendix A.

 

 

2.

Purge or Outlet Check Valve seat is worn,

2.

Shutdown and Depressurize Dryer. Refer to the Purge and

 

damaged, or fouled (allowing slight pressure

 

Outlet Check Valve Maintenance procedure which is applicable

 

leakage to enter regenerating chamber).

 

to your specific dryer model. Disassemble, clean and inspect

 

 

 

the Purge and Outlet Check Valves. Replace all worn or dam-

 

 

 

aged components as noted.

3.

Off-stream chamber’s Inlet Switching Valve

3.

Shutdown and Depressurize Dryer. Refer to the Inlet Switch-

 

or on-stream chamber’s Purge Exhaust

 

ing Valve and Purge Exhaust Switching Valve Maintenance pro-

 

Switching Valve seat is worn, damaged or

 

cedures which are applicable to your specific dryer model. Dis-

 

fouled (allowing slight pressure leakage to

 

assemble, clean and inspect the Inlet Switching Valves and

 

enter regenerating chamber).

 

Purge Exhaust Switching Valves. Replace all worn or damaged

 

 

 

components as noted.

 

 

 

Loss of power to Operating Status and Alarm

 

 

Indicators (no illumination). (Both chambers

 

 

are at line pressure, as indicated by the left and

 

 

right chamber pressure gauges.)

 

 

1.

Loss of power supply to (or at) dryer’s electri-

1.

Check power disconnect switch (or breaker) CLOSED. If tripped

 

cal disconnect switch, or breaker (customer

 

breaker or blown fuse is noted, investigate and remedy cause.

 

supplied).

 

 

2.

Loose connections at customer power con-

2.

De-energize Dryer Power Supply. Check power supply input

 

nections (H, N, GND).

 

wiring connections (H, N, GND).

3.

Control system’s power fuse (F1) is blown.

3.

De-energize Dryer Power Supply. Replace fuse if blown, in-

 

 

 

vestigate and remedy cause.

4.

Damaged components.

4.

For damaged solid state components and/or circuit boards of

 

 

 

microprocessor units, contact your local Deltech Sales Repre-

 

 

 

sentative for assistance.

Troubleshooting Guide

5 - 3

Image 57
Contents Hydrobloc LS Series Heatless Compressed AIR Dryer Page Contents Section Maintenance and Repair Scfm Hydrobloc LS Series SpecificationsModel Prefilter Afterfilter Foreword Prefilter AssemblyGeneral System Information DryerAutomatic Drain Valves Afterfilter AssemblyReceiving and Inspection Equipment HandlingMechanical Set-Up Not USE Plug or Gate Valves General Piping InformationElectrical Connection Purge Exhaust RestrictorPurge Exhaust Muffler Static Sensitive Devices Equipment Check Remote Alarm ConnectionInstrumentation Purge Flow Indicator Valve Switching Failure Option a & BMoisture Indicator Option a & B Chamber Pressure GaugesPage Automatic Drain Valve How It WorksOperation Dryer Models LS60 through LS1000 Initial Start-Up For Dryers With DEC ControllerDryer Models LS1250 and LS1500 Dryer Models LS2070 and LS2580 Operation Models LS60 through LS1000 only Normal Start-Up or Restart For Dryers With DEC ControllerDryer Models LS1250 and LS1500 Dryer Shutdown Normal Operational ChecksOperation Preventative Maintenance Schedule Maintenance and RepairAnnually Desiccant Charging ProceduresFilter Element Replacement For Dryer Models LS60 through LS1500For Dryer Models LS2070 and LS2580 Servicing The Internal Float Drain Valve If Equipped Automatic Drain Valve Components Automatic Drain Valve Disassembly and ServicingMaintenance and Repair Moisture Indicator Recharging Procedure LS60 through LS760 Inlet and Purge Exhaust Switching Valve MaintenanceInlet and Purge Exhaust Switching Valve LS1000 LS1000 Models LS1250 and LS1500 3 Inlet Switching Valve MaintenanceLS1250, LS1500 Model LS1250 only 10 2 Purge Exhaust Switching Valve MaintenanceLS1250 Model LS1500 only 11 3 Purge Exhaust Switching Valve MaintenancePurge Exhaust Switching Valve Models LS60 through LS760 Purge and Outlet Check Valve Maintenance13 11 Models LS1000 through LS1500 13 3 Purge and Outlet Check Valve MaintenanceMaintenance and Repair 4 Remote Flow Restrictor Maintenance Models LS1500 through LS2580 Flow Restrictor MaintenanceActuator Subassembly Shaft Subassembly Models LS2070 and LS2580 Purge Adjusting ValvePilot Gas Filter Maintenance Page Troubleshooting Guide Shutdown and Depressurize Dryer. Inspect desiccant De-energize Dryer Power Supply. Check power supply input Shutdown and Depressurize Dryer. Refer to the Inlet SwitchDe-energize Dryer Power Supply. Replace fuse if blown, Shutdown and Depressurize Dryer. Refer to the PurgeShutdown and Depressurize Dryer. Drain desiccant from Shutdown and Depressurize Dryer. Replace damaged, faultyRemoval of the Flow restrictor should not be done un For Models LS1500 through LS2580Less the piping to the Purge Exhaust Muffler is ad Equately supported. Failure to do so may resultDuring Repressurization Cycle Not lit, Shutdown and Depressurize Dryer. Provide aShutdown and Depressurize Dryer. Replace pressure sen PROBLEM/POSSIBLE Cause If voltage is present. De-energize Dryer Power Supply. Re Shutdown and Depressurize Dryer. Disassemble, cleanPROBLEM/POSSIBLE Cause Checks and Remedy Page Appendix a Purge Curves Table a 1 Inlet Airflow at Various Inlet Air Pressures¹ Calculation of Purge Pressure SettingOrifice Dia Gas Air Temp 100F Figure A.2 Critical Orifice Calibration Curve Figure A.3 Critical Orifice Calibration Curve Figure A.4 Critical Orifice Calibration Curve Figure A.5 Critical Orifice Calibration Curve Figure A.6 Critical Orifice Calibration Curve Figure A.7 Critical Orifice Calibration Curve Psig Pressure Purge Figure A.9 Critical Orifice Calibration Curve Purge Pressure P1 Psig Figure A.11 Critical Orifice Calibration Curve Figure A.12 Critical Orifice Calibration Curve Figure A.13 Critical Orifice Calibration Curve Appendix B Hydrobloc LS Replacement Parts 1276865 1275442 Appendix C Page Hydrobloc LSC Specifications Model Prefilter Afterfilter Table C 1 Inlet Airflow at Various Inlet Air Pressures¹ Hydrobloc LSC Purge CurvesFigure C.1 Critical Orifice Calibration Curve Figure C.2 Critical Orifice Calibration Curve Figure C.3 Critical Orifice Calibration Curve Figure C.4 Critical Orifice Calibration Curve Figure C.5 Critical Orifice Calibration Curve Figure C.6 Critical Orifice Calibration Curve Figure C.7 Critical Orifice Calibration Curve Figure C.8 Critical Orifice Calibration Curve Figure C.9 Critical Orifice Calibration Curve Figure C.10 Critical Orifice Calibration Curve Figure C.11 Critical Orifice Calibration Curve Figure C.12 Critical Orifice Calibration Curve Figure C.13 Critical Orifice Calibration Curve Hydrobloc LSC Replacement Parts 1198157 1218635 1200806 1180918 1218638 Description Quantity Model Page Page Deltech

LS60, LS2580 specifications

Deltech Fitness is renowned for providing high-quality strength training equipment, and their LS2580 and LS60 models are no exception. Both of these machines have been designed with the serious fitness enthusiast in mind, offering a range of features that cater to effective strength training routines.

The LS2580 is a multi-station home gym designed to facilitate a variety of exercises without needing multiple machines. This versatility allows users to perform a full-body workout in the comfort of their own home. One of the main features of the LS2580 is its adjustable weight stack, which provides users with the flexibility to customize their workouts. It boasts a robust and stable frame, engineered to withstand the demands of heavy usage.

With a focus on user safety, the LS2580 incorporates several safety features, including easily accessible adjustment points and non-slip grips. This makes switching between exercises seamless and reduces the risk of injury. The machine also supports a range of movements including lat pulldowns, leg presses, chest presses, and more, allowing users to target different muscle groups effectively.

On the other hand, the Deltech Fitness LS60 is a slightly simpler yet equally impressive machine that excels in offering a compact solution for strength training. The LS60 focuses on essential muscle groups, catering to those who may have limited space but do not want to compromise on their workout regimen. It is designed with a sturdy frame and is ideal for users who prioritize stability and durability in their fitness equipment.

One of the standout features of the LS60 is its adjustable seat height, making it suitable for various body types. This adaptability ensures that everyone can maintain proper form during workouts, which is crucial for both performance and safety. The LS60 also comes with various attachment points, allowing users to incorporate resistance bands or other accessories to enhance their training.

In terms of technology, both the LS2580 and LS60 emphasize user-friendly design elements that promote an intuitive workout experience. The clear labeling of each exercise station makes transitioning between workouts simple and efficient.

In summary, both Deltech Fitness LS2580 and LS60 present compelling options for fitness enthusiasts, providing a versatile and effective solution for strength training. Whether you opt for the comprehensive features of the LS2580 or the compact design of the LS60, you can expect durability, safety, and a focus on achieving your fitness goals at home.