Samsung 7100 manual Alarm Reminder Clock, Alarms are Notset, Today, Daily

Page 68

CHAPTER 2. Ошибка! Стиль не определен.

[112] ALARM REMINDER CLOCK

Allows the system administrator or technician to set or change the alarm clock/appointment reminder feature for any station. Three alarms may be set for each station and each alarm may be defined as a one-time or TODAY alarm, or as a DAILY alarm. The TODAY alarm is automatically cancelled after it rings, while the DAILY alarm rings every day at the same time. Alarm numbers are 1, 2 and 3. In the case of Station Pair assignments(MMC 740) the alarm only rings the station that is programmed and does not ring the paired station.

No	Type	Description
0	NOTSET	No alarm

1	TODAY	Alarm once only

2	DAILY	Alarm daily at set time

DEFAULT DATA

ALARMS ARE NOTSET

ACTION		DISPLAY
1)	Press Transfer button and enter 112.
1)	Press Transfer button and enter 112.	[201] ALM CLK(1)
	Display shows:	HHMM:ÆNOTSET
2)	Dial station number.(e.g., 205)
2)	Dial station number.(e.g., 205)	[205] ALM CLK(1)
	OR	HHMM:ÆNOTSET
	Press Volume button to select station and
	press Right Soft button.
3)	Dial 1~3 to select alarm.(e.g., 1)
3)	Dial 1~3 to select alarm.(e.g., 1)	[205] ALM CLK(1)
	OR	HHMM:ÆNOTSET
	Press Volume button to select alarm and
	press Right Soft button.
4)	Enter alarm time in 24-hour clock format.
4)	Enter alarm time in 24-hour clock format.	[205] ALM CLK(1)
	(e.g., 1300 for 1pm)	HHMM:1300ÆNOTSET
5)	Dial entry from above list for alarm type.(e.g., 2)
5)	Dial entry from above list for alarm type.(e.g., 2)	[205] ALM CLK(1)
	OR	HHMM:1300ÆDAILY
	Press Volume button to select alarm type and press
	Right Soft button to move cursor and return to
	step 2.

6)Press Transfer button to save and exit.

OR

Press Speaker button to advance to next MMC.

2-24	Samsung Business Communications

Image 68

Contents Programming Guide Copyright Trademarks Audience Guide ContentsPurpose Conventions Console Screen OutputFirst Edition Reference GuidesRevision History This page is intentionally left blank Instruction SymbolsRestriction Compliance with the National Version Standards Before using the Auto Record featureWhen changing the MMC 506, 807 Table of Contents Overview of Programming Procedure MMC Programming100 Assign Trunk Signal 414 MPD/PRS SignalSystem Timers STATION-WIDE Timers177 TAX Rate Setup Enable Technician ProgramCustomer Access MMC Number Card PRE-INSTALLAbbreviation List of Figures Overview of MMC Pro Gramming DCS Euro Phones 24B LCD DCS Euro Phone2 DS/ITP-5000 Series Phones DS-5038S PhoneDS/ITP-5014D/5021D Phone DS-5014S/5007S Phone Using large LCD Phones Station Level Programming Station Level Programming listMMC No MMC Name Station LockOperator Level Programming System Related MMC listStation Related MMC list Trunk Related MMC list Timer and Tone Related MMC list Group Related MMC listTables, Codes, AA, Dect and VM MMC list MMC No MMC Name Tables, Codes, AA, Dect and VM MMC list SYS. I/O Mode Technician Level Programming listOptions MGI DSP OptionsWlan Configuration Alarm ReportingSystem Alarm Assignments Maintenance BusyAlphabetically arranged Programming list MMC Name MMC No Assign ADD on ModuleBSI RF Carrier Confirm Outgoing Call Hardware Version Display Pickup Groups System SIO Mode VoIP Access Code MMC VoIP IP Table Program List by Function Phone FunctionNetworking Function VoIP FunctionWlan Function LCR Function12 VoIP Function Programming list MMC Program No Program DescriptionAuto Attendant/Voice Mail Function Diagnosis Function Hotel FunctionPage MMC Programming Type Description Station LockALL Stations Unlocked Assign COS Contents Assign Station COSALL Station Passcodes Default passcodesChange User Passcode Type Call ForwardNone System Timers STATION-WIDE TimersTo answer the C.O. call automatically SET Answer ModeALL Phones Ring Select all phones Dial 0, 1 or 2 to change ring mode Dial Volume Up/Down keysStation Name Display shows Dial station number.e.g Station Speed Dial Program ButtonsAssign Speed Block Station Speed Dial Name Station Speed DialKey Feature Extender KEY ExtenderWhen using the Right Soft button Copy KEY ProgrammingStation KEY Programming System KEY ProgrammingStation Status Status DescriptionPickup Groups Assign BOSS/SECRETARYAssign Station Group Assign Station to page ZoneCountry Western Clock 12 Hour Display Lower Case Mode DescriptionDate Display Assign Date and Time Feature Default Description Station ON/OFFSee Description Some Options Depend on Country Not CONT.CIDAuto ANS CO OFF Enblock 2LCD OFFAssign COS Contents Frequency Phone VolumePhone Ring Tone Alarm Reminder Clock Alarms are NotsetNotset TodayAlarm and Message View Memo Number Phone Volume Dial volume type.e.g SET Programmed Message No Messages SelectedAlarm and Message Alarm Reminder Clock Edit Text Message Blank MessageConference Group Allow Group Conference Caller ID Display Number FirstAllow Caller ID Assign Review BlockLarge LCD Options Option DescriptionMMC 719 Idle Display Language Phone LanguageEnglish None News Display Speed Answer Mode Executive StateExec State StateinRelated Items Invalid Feature DescriptionShow License Status Disable SYSTEM-WIDE TimersOpen Customer Programming Change Customer PasscodeChange Customer Passcode PasscodeWlan Regst Change Feature PasscodeRing Plan Disa Alarm Alarm CLR Dect Regst Assign Disa Trunk When setting the MMC Assign UA DeviceCommon Bell Control Ringing Device DescriptionAssign UA Device Common Bell ControlContinuous Assign Loud Bell UnassignedBARGE-IN Type No BARGE-INNo BARGE-IN With ToneWhen using the MMC Assign VM/AA PortNormal Port 1VMAA, 0NORMALICM Ring ICM RingCO Ring Data RingAssign ADD-ON Module MasternoneOption Default Description Customer ON/OFF PER TenantCancel VPN Enable OFFICM EXT FWD OFF Did ERR Tone OFFCleaned SGR ALL OUT OFFChain FWD TRK Moniter OFFVoip Realrbt OFF CO-CO TM ALL OFFSmdr LOG OFF ALLDial option number.e.g Door Ring Assignment Station GroupDisa Alarm Ringing Station ALL Ring PlansTraffic Report Option Auto Print OFFDial 0 for manual or 1 for automatic print Relay Type Isdn Service Type VoiceExtension Type Normal StationDial 0 5 to select station type FAX Pair Extension TypeWAKE-UP Announcement AA Group None Message no None Group Busy NoneAA Group Message noEnter the AA group number Customer ON/OFF PER Station LCR Digit Table LCR Time TableAssign Station COS Enter the next ring plan class of service.e.g KEY Extender Pickup GroupsNo Pickup Groups Assigned Assign BOSS/SECRETARY Assign EXTENSION/TRUNK USE Dial YES ANS YESCopy Station Usable Assign Forced Code Account CodeHOT LINE/OFF Hook Selection Assign Background Music Source Assign Trunk MOH SourceAssign Station MOH Source ToneLCR Route Table LCR Class of ServiceLeast Cost Routing COS Allow Caller ID RCV YES SND YESRCV SNDDisconnect Confirm Outgoing CallConfirm Tone Customer SET Relocation Relocate 48B 64B IDCS Allowed 12B 24B28D 18D IDCS 28DSLT Euro 6B Euro 12B Euro 24B 48B AOM 64B AOM Copy Station Usable STATION/TRUNK USE GroupAssign STATION/STATION USE Dial YESCadence Distinctive RingingTone Dial trunk or station number.e.g Branch Group MMCPreset Forward no Answer When using PRE FWD Busy option in MMCINT EXTDial call type 0, 1 or 2.e.g Calling Party Number EmptyBRI Options PRI OptionsRingback Tone Message Customer ON/OFF PER Trunk Display show Trunk LINE/PBX Line ALL Trunks CO LineTrunk Dial Type ALL Trunks DtmfDtmf Type Dial Pulse TypeClass Description Trunk Toll ClassALL Trunks F-STN Enter day toll class.e.g., 2 for CLS-B Trunk Name Station NameTrunk CO TEL Number Entering NumbersAssign Ring Plan Time ALL Trunks Ring Default Operator GroupTrunk Ring Assignment Forced Trunk Release Assign Trunk MOH Source Trunk Status Read Follows TrunkCustomer ON/OFF PER Trunk Trunk LINE/PBX LineTrunk Dial Type Trunk Toll ClassAssign Disa Trunk ALL Trunks NormalImmediate Start Assign Trunk SignalSignalling condition type 414 MPD/PRS Signal NonenormalPRS MPDTRUNK-WIDE Timers MMCReport Trunk Abandon Data ALL Trunks Report YESReport no Report YES417 E1/PRI CRC4 Option CRC4 onBRI and PRI Card Restart ModeBRI Options Channel ANY YES Power Feed no Display shows first BRI channel Calling Party Number Trunk CO TEL NumberBRI & PRI Card Restart MSN DigitPRI Mode PRI OptionsNormal Same ConnidDial first PRI trunk number in PRI card.e.g MSN Digit CW YES OPT AcceptTrunk COS ALL Ring Plans COSALL TRK COS Trunk 423 S/T ModeBRI S0 Mapping BRI S0 Mapping CID Trunks Normal TrunkTrunk Gain Control Trunk Gain DescriptionAssign TRUNK/TRUNK USE Default Data Action Display SET H-TRKCosting Dial Plan Cost RateALL TRUNKS/ALL Dial Plans ALL Cost Rates Assigned Connection Status Display trunk connection statusDisplay trunk status in conference Station Status Trunk TMC Gain Default Data Action 437 16TRK Gain ControlSee Description Counter Default DescriptionSYSTEM-WIDE Counters Enter number from above list.e.g System Timers Timer Name Default Range Unit DescriptionDisplay Delay TM CO Confirm TimeCO-CO Disconnect Confirm Tone TMMCL Delay Time First Digit TimeHOK Flash MAX TM HOK Flash MIN TMPower Down Time MS LED on TimeOFF Hook Ring INT Ohva Answer TimeSee Description Some Timers Depend on Country When timers value is ‘0’Display shows first timer value STATION-WIDE Timers Call Forward TRUNK-WIDE Timers Description RangeConn Delay Disa Answr151 Pulse MAKE/BREAK Ratio MAKE/BREAK 33 Make Pulses PER Second 10 PPSMAKE/BREAK Ratio Pulse PER SecondAssign Date and Time Type Description RangeUnit milliseconds When changing the MMCTone Cadence Terrupt Assign Ring Plan Time Start Time End TimeStart None END None Ring PlanCall Cost Unit Cost PER MP 0200 PENCE, Call Cost Rate 100 PercentDisplay Description Unit Cost PER MPSLI Ring Cadence 160 Interrupted MSG Waiting Lamp CadenceInterrupt LED 1000MS-ON 1000MS-OFF Holiday Assignment No Holiday Assigned Follows Ring PlanHotel Timer Room Clean TimeCheck OUT Time Check in END TMTone Source Assign Date and Time Daylight AssignmentNo YY Start END Assign Operator Group Type 2 UCD Assign Station GroupType 1 UCD Groups Calls to a group Normal Group Dial next feature option and continue Station Group Name Assign Trunk Group Trunk groupLCR Programming Assign Station to page Zone No Stations AssignedAssign External page Zone Assign Speed Block System 200 Entries Stations 1 Block AssignedStation Speed Dial Name Assign System Speed DialUCD Options Final Destination Ring Next TimeUCD Recall Time WRAP-UP TimeAuto LOG OUT AlloutæfinalAgent PIN no Group Busy NextPress Volume button to select UCD group or dial Smdr Options Assign Review BlockPhones 10 Bins Call LOG Block Allow Text Messaging Allow Group Conference STATION/TRUNK USE Group ALL Stations ALL Trunks NoneAssign STATION/STATION USE Assign TRUNK/TRUNK USEMGI Group Display shows the first available option MGI User Copy COS Contents Assign COS Contents Feature YES Flash YESFOLLOW-ME YES Forward YESREM. Hold YES RNG Plan YESSecure YES SET RlocDial COS.e.g Toll Deny Table ALL Entries are SET toToll Allowance Table Toll Deny Table Assign Wild Character Entries SET to Z Entries SET toAssign System Speed Dial ANS/RLSSystem Speed Dial by Name No NamesAssign System Speed Dial Authorization Code Assign Forced CodeAccount Code Toll Pass CODE/SPECIAL Code Table Special Code DescriptionToll Restriction LCR Digit Table LCR Digit 0001 Digit LCR Digit 0005 DigitLCR Time Table LCR Route Table LCR Class of Service LCR Modify Digit Table Digit String KEYOption Description Max. No. of Digit Entries NOF DEL DGTEnter digits to be appended.e.g Did Number and Name Translation DGTPRI NameEnter valid index numbere.g., 005 via dial keypad Enter call wait option via dial keypad Programmed Station Message Leave a Message On Vacation Gone HomeUK LCR Option Network CodePIN Code CCC OptionLCR Modify Digit Table UCD Agent ID UCD OptionsMY Area Code Idle Display Copy KEY Programming Restore Save Station KEY ProgrammingStation KEY Programming BILLHotel FeatureBOOTHHotel Feature Message Cancel Path ReplacementEasy Alarm SET to Isdn Supplementary ServiceSystem Alarms TimerHeadset Mode Universal Answer Voice Mail AdministrationEnter selected station number.e.g System KEY Programming Type of Phone DescriptionBTN Sets EU 6B SetsSee Default Data in MMC Dial Numbering Plan Type of Dial No DescriptionVirt EXT Dial no MGI Dial noIP STN Dial no Wlan Dial noChout None Choice NoneConf Conference Conp None Connected Name Display Credit NoneReject None Ohva Reject Ring Plan RSV RTO None Ring Plan Time Override Selfid Self System IDSee Description Feature Codes Depend on Country Dial option number to make selection.e.g Smdr Options Incoming AnswerIntercom Call KEY MMC IN/OUTDial the option number.e.g System Version Display CID Translation Table When changing the COS Station PairCosting Dial Plan MMC 749, Rate Calculation TableCost Rate Currency values£ or € Rate Calculation TableALL Cost Rates no Data Dial option number 0-4.e.g VM Card Restart ALL Options are noMBX Download Assign Mailbox ALL Stations YES ALL Groups noAuto Record Dial VM number via dial keypad 5000 VM Halt RestartVM Alarm Threshold 80%Not Used When the first Built-In Voice Mail port is used for VmmohAssign Vmmoh VM IN/OUT IN/OUTVM DAY/NIGHT ALL Ring Plans DAYREJ CLI RingingCLI Allow Caller ID Code Description Item Cost TableNo Entries Enter valid code numbere.g., 02 via dial TAX Rate Setup ALL Rates are %TAX Rate ValueEnter the tax rate or value via dial keypad Room Cost Rate ALL Rates are 100%Option Description Default Second LCRLCR Class LCR TimeLCR Route Number PlanEnable Technician Program Default Passcode Change Technician PasscodeCustomer Access MMC Number TX Level and Gain SVMiAction Display Card PRE-INSTALL When a card is removed and a different type card is insertedAre YOU SURE?NO Phone Volume Control Phone Volume LevelDepends on Phone Typeshown for 21D 21DHalt Processing ProcReset System Clear MemoryFast Restart System Restart are YOU SURE?YESSET Country Code Hotel Timer TAX Rate SetupHotel Operation FAX PairCustomer Database Copy Clear McdbCopy to Sram Copy to McdbIf you select YES, the display shows Program Download MC File Control File Name DescriptionPress Volume button to confirm program type Assign System Link ID Assign Network TrunkAssign Network COS Ethernet ParametersAssign Network Trunk NormalVirtual Extension Type BTN SETLarge SET BTN LCDEnter virtual extension number Assign Network COS Dial the class of service number.01-30 Network Dial Translation Enter YES/NO to assign Mailbox to remote Assign Networking Options Dial the option number Assign System Reference Clock Priority 1 C1-S0 Priority 2 C1-S1 Priority 3 SelfLAN Printer Parameters Enter type of data to be printed Ethernet Parameters Parameter DescriptionCTI Server Addr Ethernet ParametersDisplay shows the system IP address MGI Parameters Version Card Reset no IP Type Private IP onlyVoIP Access Code SIP Options Voip IP TableOptions Voip Access Code When changing IPVoIP IP Table TB00 ENTRY00 MMC 830 System IP Addr ALL Others EmptyParameter Description Default 834 H.323 OptionsGateway Call ID Fast Setup Disable Fast Setup Enable MGI DSP Options Outband TOS FieldFAX Retry RTP CHK TMMGI Parameters 836 H.323 GK Options GRQ Send USE Multi E.164Lists GK RegisteredSIP Options Port Signal Port ProvisionalINV.NO Resp GEN.NORegistered GW Service Timer 0NONE, 1UPDATE, 2REINVITE ServerSIP GW Domain315 SIP User Private IP Addresses IP Phone Information Upgrade Jitter BUFMMC 841 ITP DSP Para Down = Phone Data Time ZoneMGI Group MGI UserMGI DSP Options System IP OptionsSystem IP Options CTI Link Option ITP DSP ParaSYS Data ITP TX GAIN/HSETCommand ITP TX GAIN/MICITP RX GAIN/SPKR ITP VersShow License Status Wlan Parameters Parameter Description Defaultms When the cursor is on WLAN, press Volume button BWBS=BASIC WBS Range is 0-99900 ms.Default 6000 ms WIP Information Wlan Configuration Wlan IP/MAC ListWlan IP/MAC List WIP InformationWlan Configuration Enter WEP KEY values when the WBS WEP SER System Resource Display Only MMC Dtmfr DSP’S CID DSP’S R2MFC DSP’S Conf GROUP’SAlarm Reporting View AlarmsClear Alarm BUF Print Alarm BUFEnter desired option Code Alarm Name Definition MJA MCP2 Error System Fault System Alarm AssignmentsAlarm Notification DSP Error System DSP Fault Code Alarm Name DefinitionLCP/TASK Error LCP or Task Fault Dtrk Error Isdn or E1 card Fault MGI Error MGI card Fault Minor Error Minor Fault with Alarm Buffer saving Minor Error Minor Fault without Alarm Buffer saving ALL OFF Alarm ReportingMaintenance Busy Maintenance Busy ALL IdleDisplay shows busy functions Diagnostic Time No Diagnostic Time SETLAN Tech Programming LogsNnnn Virtual Cabinet SET Type RangeMMC 724 Number Plab MMC 822 VIR.EXT Type MP Card Hardware Version DisplayOnly MMC System Options Auto Update Time Assign Speed Dial Block System Speed DialAccess NUM Node InfoTEL Number MAX CountInitialize Port AAA ACDALG AMEDasl DectDhcp DpimIPC IpdcIPM IP-SCPOPX PATPBA PCBSLI SmdrSmtp STAWLI WANWIM Programming Guide

Related manuals

Manual 77 pages 9.02 Kb