Kohler K-12106-H manual Ordering Information, Required Electrical Service, Product Information

Page 4

1. ROUGHING-IN: K-12105-H*, K-12106-H*

A. ORDERING INFORMATION

Applicable product:

 

 

Left outlet

K-12105

shown

Right outlet

K-12106

not shown

Accessories/hardware:

 

 

Drain

K-7161-AF

recommended

Jet trim kit

K-9696

required

MasterShower

K-9500

recommended*

Handshower

 

 

Paladar valve only trim

K-T14542-4

recommended

Paladar Rite-Temp valve

K-304-K

recommended

Bath spout

K-6855

recommended

Dome light

K-1570

optional

Glassworks bypass door

K-9864

optional

or

 

 

Forum bypass door

K-703012

 

* Dimensions illustrated

B. REQUIRED ELECTRICAL SERVICE

Dedicated branch circuit required, protected with Class A Ground-Fault Circuit-Interrupter (GFCI):

Pump/control

120 V, 20 A, 60 Hz

C. PRODUCT INFORMATION

ADA compliant

 

 

Fixture*:

basin area

top area

weight

Bathing well

44º x 23º

51º x 26º

265 lbs.

 

water depth

capacity

 

To overflow

13º

55 gals.

 

Configuration

 

 

1-piece

Drain Outlet

 

 

2-1/4º D.

* Approximate measurements for comparison only.

Pump

high HP

low HP

V

Hz

A

2-speed

1

1/8

120

60

16.5

D. INSTALLATION NOTES

Read the entire installation instruction before beginning the installation.

Unit is not drilled for supply fittings.

Shimming may be required to level fixture.

For optimum accessibility, specify faucets and fittings to install and operate within the control area shown.

Pump is supplied with a grounding-type plug-in cord. Locate the outlet behind the whirlpool, and within 24º of the pump.

PUMP/CONTROL ACCESS

 

 

 

37º

18º

 

 

13º

 

 

ROUGHING-IN NOTES

Fixture conforms to ANSI Standard Z124.2. All dimen- sions are nominal.

* Recess opening must be 65º x 84-1/4º.

No change in measurements if connected with drain il- lustrated.

Minimum access panel:

Pump/control

20º W x 15º H

required

ELBOW7/8º

SUPPLY

56º

*64-3/4º

Stud opening tolerance (+ 1/4º ± 0º). When fire rated wall is specified, dimensions are to the inside of the wall board. Some shimming between stud frame and fixture

C

L SPOUT

20º

1-5/16º

*84º

19º

3/4º

2-7/8º

 

1-1/2º O. D.

may be required.

Provide clear floor space per ANSI A117.1, and as shown.

 

Represents control area for faucets.

 

Represents 24º wall mount slide bar.

 

Represents clear floor space for 36º

36º

x 60º side entrance.

 

60º

 

 

Represents clear floor space for 48º

48º

x 60º side entrance.

 

60º

 

115982-2-BA(-)

4

Kohler Co., Kohler, WI

Image 4
Contents Freewill Barrier Free Bath Whirlpools 12105-H* K-12106-H Important Safety Instructions Table of Contents IntroductionRequired Electrical Service Installation NotesOrdering Information Product InformationProduct Notices Product RequirementsInstallation Requirements NEW or Replacement Installation RequirementsElectrical Requirements Tools RequiredUser Access Considerations Site RequirementsOLD Bath Removal Subfloor PreparationPlumbing Access Considerations Other Installation ConsiderationsBefore Installing Unit Partially Install Bath DrainStud Pocket Preparation Plumbing PreparationInstall the Whirlpool Whirlpool SET-INInstall Plumbing Pump Banding Strap CUTWater Test Whirlpool and Electronics Electrical ConnectionsIdentify Electrical Requirements Complete Installation Install Whirlpool Trim KITInstall Faucet and Drain Trim Install Extra Grab BarsCLEAN-UP After Installation Install Shower RODShower Door Installation Confirm Proper OperationFlexjet Installation Troubleshooting ProceduresOperating Sequence Symptoms Troubleshoot Whirlpool SystemProbable Causes Recommended Action