Analog Devices ADSP-21369 system manual Reset LEDs LED10 and LED12, LED and Push Button Locations

Page 53

EZ-KIT Lite Hardware Reference

Figure 2-6. LED and Push Button Locations

Reset LEDs (LED10 and LED12)

When LED10 is lit (red), the master reset of all the major ICs is active. When LED12 is lit (red), the USB interface chip (U4) is being reset. The USB chip is reset only on power-up, or if USB communication has not been initialized.

ADSP-21369 EZ-KIT Lite Evaluation System Manual

2-15

Image 53

Contents ADSP-21369 EZ-KIT Lite Evaluation System Manual Trademark and Service Mark Notice Limited WarrantyCopyright Information DisclaimerRegulatory Compliance Page Contents Using EZ-KIT Lite ADSP-21369 EZ-KIT Lite Evaluation System Manual Vii Bill of Materials Schematics Index Preface Page Preface Page Intended Audience Manual ContentsPurpose of This Manual What’s New in This Manual What’s New in This ManualTechnical or Customer Support Product Information Supported ProcessorsProduct Information MyAnalog.comProcessor Product Information Title Description Related DocumentsEach documentation file type is described as follows Online Technical DocumentationAccessing Documentation From Web Accessing Documentation From VisualDSP++Accessing Documentation From Windows VisualDSP++ Documentation Set Printed ManualsHardware Tools Manuals Processor ManualsPreface Data Sheets Notation Conventions Notation ConventionsPreface Xxiv ADSP-21369 EZ-KIT Lite Evaluation System Manual Using EZ-KIT Lite Package Contents Using EZ-KIT Lite Default ConfigurationInstallation and Session Startup Installation and Session StartupUsing EZ-KIT Lite Evaluation License Restrictions Evaluation License RestrictionsExternal Memory Start Address End Address ContentElvis Interface Elvis InterfaceAnalog Audio LEDs and Push Buttons LEDs and Push ButtonsPB1 SW8 FLAG1/~IRQ1 PB2 Example Programs Example ProgramsBackground Telemetry Channel Sors/resources/crosscore/emulators/index.html. For more Background Telemetry Channel EZ-KIT Lite Hardware Reference System Architecture System ArchitectureEZ-KIT Lite Hardware Reference External PortDAI Interface ADSP-21369 DPI InterfaceFlag Pins Expansion Interface External PLLBoot Mode and Clock Ratio Select Switch SW2 Switch SettingsSwitch Settings Jtag Emulation PortOFF Core Clock Rate Configuration Codec Setup Switch SW3Uart Enable Switch SW5 Electret Microphone Select Switch SW4Push Button Enable Switch SW7 Loop-Back Test Switches SW6 and SW14Elvis Function Generator Configuration Switch SW13 Elvis Oscilloscope Configuration Switch SW1General Purpose LEDs LED1-8 Power LED LED9LED and Push Button Locations Reset LEDs LED10 and LED12Push Buttons SW8-11 USB Monitor LED LED11VCO Select Jumper JP1 Board Reset Push Button SW12Jumpers Jumper Locations 10. VCO Select Jumper JP1 JumpersElvis Voltage Selection Jumper JP3 Elvis Select Jumper JP2Expansion Interface Connectors J1-J3 ConnectorsConnectors Elvis Programmable Flag Jumper JP4Connector Locations Audio Out RCA Connector J5 Audio In RCA Connector P10Power Jack J4 Headphone Out Jack P7Spdif Coax Connectors P8 and P9 RS-232 Connector P1DAI Header P4 USB Connector P5DPI Header P3 Jtag Header P2 Connectors Bill of Materials Description Reference Designator Manufacturer Part Number Bill Of Materials VR5 ADI Switchcraft PJRAN1X1U01 BLK SPST-MOMENTARY SWT013 2A S2ARECT DO-214AA Panasonic ERJ-2GEJ472X DIGI-KEY P1.5KCFCT-ND Yageo ERJ-3RSFR10V Panasonic ECJ-1VC1H101J RED-SMT LED001 LED10,LED12 Panasonic ADSP-21369 EZ-KIT Lite Evaluation System Manual ADSP-21369 EZ-KIT Lite Schematic Devices DSP Memory Analog Audio Audio OUT DAC3 Left Audio in & Headphone OUT Analog DSP IO Current PUSHBUTTONS, LEDS, & Reset Expansion Interface Power Index Index Jtag SPI