Analog Devices ADSP-21369 system manual LEDs and Push Buttons

Page 34

LEDs and Push Buttons

routing unit (SRU). It is also necessary to disable the on-board audio oscillator from driving the audio codec and the processor’s input pin. For instructions on how to configure the clock, refer to “Codec Setup Switch (SW3)” on page 2-10.

The AD1835A codec can be configured as a master or as a slave, depend- ing on the DIP switch settings. In master mode, the AD1835A drives the serial port clock and frame sync signals to the processor. In slave mode, the processor must generate and drive all of the serial port clock and frame sync signals. For information on how to set the mode, refer to “Codec Setup Switch (SW3)” on page 2-10.

The AD1835A audio codec’s internal configuration registers are config- ured using the SPI port of the processor. The DPI pin 4 (DPI4 register) is used as the select for the device. For information on how to configure the multichannel codec, refer to the codec’s datasheet, which can be found at

http://www.analog.com/en/prod/0,2877,AD1835A,00.html.

The RCA connector (P10) is used to input analog audio. When using an electret microphone on this connector, configure the SW4 switch according the instructions in “Electret Microphone Select Switch (SW4)” on page 2-11. The four output channels connect to the RCA connector J5. Channel 4 of the codec connects to the headphone jack P7. For more information about the connectors see “Connectors” on page 2-20.

Example programs are included in the EZ-KIT Lite installation directory to demonstrate how to configure and use the board’s analog audio interface.

LEDs and Push Buttons

The EZ-KIT Lite has eight general-purpose user LEDs and four gen- eral-purpose push buttons.

1-10	ADSP-21369 EZ-KIT Lite Evaluation System Manual

Image 34

Contents ADSP-21369 EZ-KIT Lite Evaluation System Manual Copyright Information Limited WarrantyTrademark and Service Mark Notice DisclaimerRegulatory Compliance Page Contents Using EZ-KIT Lite ADSP-21369 EZ-KIT Lite Evaluation System Manual Vii Bill of Materials Schematics Index Preface Page Preface Page Purpose of This Manual Manual ContentsIntended Audience Technical or Customer Support What’s New in This ManualWhat’s New in This Manual Supported Processors Product InformationProcessor Product Information MyAnalog.comProduct Information Related Documents Title DescriptionOnline Technical Documentation Each documentation file type is described as followsAccessing Documentation From Windows Accessing Documentation From VisualDSP++Accessing Documentation From Web Hardware Tools Manuals Printed ManualsVisualDSP++ Documentation Set Processor ManualsPreface Data Sheets Notation Conventions Notation ConventionsPreface Xxiv ADSP-21369 EZ-KIT Lite Evaluation System Manual Using EZ-KIT Lite Package Contents Default Configuration Using EZ-KIT LiteInstallation and Session Startup Installation and Session StartupUsing EZ-KIT Lite Evaluation License Restrictions Evaluation License RestrictionsStart Address End Address Content External MemoryElvis Interface Elvis InterfaceAnalog Audio LEDs and Push Buttons LEDs and Push ButtonsPB1 SW8 FLAG1/~IRQ1 PB2 Background Telemetry Channel Example ProgramsExample Programs Sors/resources/crosscore/emulators/index.html. For more Background Telemetry Channel EZ-KIT Lite Hardware Reference System Architecture System ArchitectureExternal Port EZ-KIT Lite Hardware ReferenceDAI Interface DPI Interface ADSP-21369Flag Pins External PLL Expansion InterfaceSwitch Settings Switch SettingsBoot Mode and Clock Ratio Select Switch SW2 Jtag Emulation PortOFF Codec Setup Switch SW3 Core Clock Rate ConfigurationElectret Microphone Select Switch SW4 Uart Enable Switch SW5Loop-Back Test Switches SW6 and SW14 Push Button Enable Switch SW7Elvis Oscilloscope Configuration Switch SW1 Elvis Function Generator Configuration Switch SW13Power LED LED9 General Purpose LEDs LED1-8Reset LEDs LED10 and LED12 LED and Push Button LocationsUSB Monitor LED LED11 Push Buttons SW8-11Jumpers Board Reset Push Button SW12VCO Select Jumper JP1 Jumpers Jumper Locations 10. VCO Select Jumper JP1Elvis Select Jumper JP2 Elvis Voltage Selection Jumper JP3Connectors ConnectorsExpansion Interface Connectors J1-J3 Elvis Programmable Flag Jumper JP4Connector Locations Power Jack J4 Audio In RCA Connector P10Audio Out RCA Connector J5 Headphone Out Jack P7RS-232 Connector P1 Spdif Coax Connectors P8 and P9DPI Header P3 USB Connector P5DAI Header P4 Jtag Header P2 Connectors Bill of Materials Description Reference Designator Manufacturer Part Number Bill Of Materials VR5 ADI Switchcraft PJRAN1X1U01 BLK SPST-MOMENTARY SWT013 2A S2ARECT DO-214AA Panasonic ERJ-2GEJ472X DIGI-KEY P1.5KCFCT-ND Yageo ERJ-3RSFR10V Panasonic ECJ-1VC1H101J RED-SMT LED001 LED10,LED12 Panasonic ADSP-21369 EZ-KIT Lite Evaluation System Manual ADSP-21369 EZ-KIT Lite Schematic Devices DSP Memory Analog Audio Audio OUT DAC3 Left Audio in & Headphone OUT Analog DSP IO Current PUSHBUTTONS, LEDS, & Reset Expansion Interface Power Index Index Jtag SPI