Analog Devices ADSP-21369 system manual Jumpers, Jumper Locations 10. VCO Select Jumper JP1

Page 56

Jumpers

Figure 2-7. Jumper Locations

Table 2-10. VCO Select Jumper (JP1)

JP1 Setting	Mode


OFF	VCO Output frequency x ½ (default)

ON	VCO output frequency x 1.0

2-18	ADSP-21369 EZ-KIT Lite Evaluation System Manual

Image 56

Contents ADSP-21369 EZ-KIT Lite Evaluation System Manual Limited Warranty Trademark and Service Mark NoticeCopyright Information DisclaimerRegulatory Compliance Page Contents Using EZ-KIT Lite ADSP-21369 EZ-KIT Lite Evaluation System Manual Vii Bill of Materials Schematics Index Preface Page Preface Page Intended Audience Manual ContentsPurpose of This Manual What’s New in This Manual What’s New in This ManualTechnical or Customer Support Supported Processors Product InformationProduct Information MyAnalog.comProcessor Product Information Related Documents Title DescriptionOnline Technical Documentation Each documentation file type is described as followsAccessing Documentation From Web Accessing Documentation From VisualDSP++Accessing Documentation From Windows Printed Manuals VisualDSP++ Documentation SetHardware Tools Manuals Processor ManualsPreface Data Sheets Notation Conventions Notation ConventionsPreface Xxiv ADSP-21369 EZ-KIT Lite Evaluation System Manual Using EZ-KIT Lite Package Contents Default Configuration Using EZ-KIT LiteInstallation and Session Startup Installation and Session StartupUsing EZ-KIT Lite Evaluation License Restrictions Evaluation License RestrictionsStart Address End Address Content External MemoryElvis Interface Elvis InterfaceAnalog Audio LEDs and Push Buttons LEDs and Push ButtonsPB1 SW8 FLAG1/~IRQ1 PB2 Example Programs Example ProgramsBackground Telemetry Channel Sors/resources/crosscore/emulators/index.html. For more Background Telemetry Channel EZ-KIT Lite Hardware Reference System Architecture System ArchitectureExternal Port EZ-KIT Lite Hardware ReferenceDAI Interface DPI Interface ADSP-21369Flag Pins External PLL Expansion InterfaceSwitch Settings Boot Mode and Clock Ratio Select Switch SW2Switch Settings Jtag Emulation PortOFF Codec Setup Switch SW3 Core Clock Rate ConfigurationElectret Microphone Select Switch SW4 Uart Enable Switch SW5Loop-Back Test Switches SW6 and SW14 Push Button Enable Switch SW7Elvis Oscilloscope Configuration Switch SW1 Elvis Function Generator Configuration Switch SW13Power LED LED9 General Purpose LEDs LED1-8 Reset LEDs LED10 and LED12 LED and Push Button LocationsUSB Monitor LED LED11 Push Buttons SW8-11VCO Select Jumper JP1 Board Reset Push Button SW12Jumpers Jumpers Jumper Locations 10. VCO Select Jumper JP1Elvis Select Jumper JP2 Elvis Voltage Selection Jumper JP3Connectors Expansion Interface Connectors J1-J3Connectors Elvis Programmable Flag Jumper JP4Connector Locations Audio In RCA Connector P10 Audio Out RCA Connector J5Power Jack J4 Headphone Out Jack P7RS-232 Connector P1 Spdif Coax Connectors P8 and P9DAI Header P4 USB Connector P5DPI Header P3 Jtag Header P2 Connectors Bill of Materials Description Reference Designator Manufacturer Part Number Bill Of Materials VR5 ADI Switchcraft PJRAN1X1U01 BLK SPST-MOMENTARY SWT013 2A S2ARECT DO-214AA Panasonic ERJ-2GEJ472X DIGI-KEY P1.5KCFCT-ND Yageo ERJ-3RSFR10V Panasonic ECJ-1VC1H101J RED-SMT LED001 LED10,LED12 Panasonic ADSP-21369 EZ-KIT Lite Evaluation System Manual ADSP-21369 EZ-KIT Lite Schematic Devices DSP Memory Analog Audio Audio OUT DAC3 Left Audio in & Headphone OUT Analog DSP IO Current PUSHBUTTONS, LEDS, & Reset Expansion Interface Power Index Index Jtag SPI