Oricom MI40 manual Out of Range Warning, Auto Answering, Recall Timing, Handset Name

Page 30

Out of Range Warning

When the handset is too far away from the base during standby and the link is lost with the base, the display will show BS SEARCH and

the icon will blink.

•Bring the handset nearer to the base so that the signal gets stronger.

•When the signal between the handset and base re-establishes, the display will go to standby and the icon will be steady.

When the handset is too far away from the base during a call, user will hear an alert tone through the earpiece.

•Bring the handset closer to the base so that the signal gets stronger.

•If you fail to bring the handset back in range with the base, your call would be disconnected.

Auto Answering

When the function is activated, user is able to answer a call by lifting

the handset out of the base cradle without having to press the key.

•Press. Use to scroll through the menu until the display reads SETTINGS.

•Press. Use to scroll through the menu until the display reads AUTO ANS.

•Press.

•To activate:

oUse to select ON.

oPress. User can answer a call by lifting the handset out of

the base cradle without having to press the key.

•To de-activate:

oUse to select OFF.

oPress. User will need to press the key to answer a call no matter the handset is on the base cradle or out of the base cradle.

Recall Timing

Recall timing default settings are: Australia 100ms and New Zealand 600ms. You should not need to change these settings.

If when you are using network services or a PBX the button does not work you can select a different setting.

•Press. Use to scroll through the menu until the display reads SETTINGS.

•Press. Use to scroll through the menu until the display reads FLASH TIME.

•Press. Use to select from the two durations choose Flash 1 for Australia and Flash 2 for New Zealand.

•Press on a selection to confirm and exit to FLASH TIME.

•Press and hold will exit to standby.

Handset Name

If you choose to you may programme each handset with its own name to be displayed during standby.

•Press. Use to scroll through the menu until the display reads DISPLAY.

•Press. Use to scroll through the menu until the display reads LABEL.

59 of 72

60 of 72

Image 30

Contents MI40 User guide Caller ID Using the Phone BookAdditional Features Answering MachineUsing Additional Cordless Handsets Appendix Default Settings Warranty InformationSafety Information Getting StartedUnpacking Your Telephone LCD Display on the HandsetIcon Name Description Basic Steps to Install Battery Level IndicationCharging the Handset Call Log Menu Menu OverviewPhonebook Menu Redial MenuUsing Traditional Dialling Basic OperationsTo End a Call Using Pre-Dialling Using Quick DiallingUsing Direct Dialling Redial the Last Dialled Number Using Last Number Re-Dialling functionRedial the Last Dialled Number by Using Pre-dialling Save the Redial Number in the PhonebookAdjusting the Handset Ringing Volume When the handset is on the base unit, lift the handsetWhen the handset is not on the base unit Delete a Redial NumberUsing a Headset Not supplied Adjusting the Receiver VolumeHandsfree Operation Using the Handsfree Speaker Microphone Mute / Un-muteStoring an Entry Using the Phone BookLow Power Mode Reviewing the PhonebookDialling a number from Phonebook Deleting a Phonebook EntryVIP Ringing Melody Call Log Caller IDCall Waiting Caller ID Reviewing the Call LogDeleting a CID Record Answering MachineSaving the CID record into phonebook Call Back from the Call LogOutgoing Message OGM Answering ModeChanging Answering Mode Recording OGMAnswering Machine Quick OFF Deleting the customized OGMAnswering Machine On / Off MemoIncoming Message ICM Playing MemoDeleting Memo Recording ICMRing Delay Playing ICMDeleting ICM Alert Tone Message LengthSpeaker Filtering ALL Call ScreeningOFF ExemptRemote Access Code Block the BlockerSOS Code Remote Access to the Answering Machine Remote Access ShortcutsRemote Access Responses Adding a new Network Service Additional FeaturesNetwork Services Reviewing Network ServicesDialling out the Service Number Editing Network Service NumberDelete a Network Service Call Barring FeaturesPrefix Following call barring options can be selectedRinger Melody for External Calls Ringer Melody for Internal CallsAlert Tones Ringing Volume for BaseBase Ringer Melody for External Calls ChargingRecall Timing Out of Range WarningAuto Answering Handset NameCall Timer Backlit LCDRegistration Using Additional Cordless HandsetsDelete All Records Base SelectionOr Use Pre-Dialling To end intercom callMonitor Conference CallRoom Monitoring De-register a HandsetReset Factory Default Change the PIN Code for BaseAppendix Default Settings Warranty Information