Oricom MI40 Using Additional Cordless Handsets, Appendix Default Settings Warranty Information

Page 3

Ringing Volume for Base

57

Base Ringer Melody for External Calls

57

Alert Tones

58

Out of Range Warning

59

Auto Answering

59

Recall Timing

60

Handset Name

60

Call Timer

61

Backlit LCD

62

Delete All Records

63

Using Additional Cordless Handsets

63

Registration

63

Base Selection

64

Making Internal Calls

65

Or Use Pre-Dialling

65

To end intercom call

65

Receiving external call during Internal Call

66

Inquiry Call

66

Call Transfer

66

Conference Call

67

Room Monitoring

67

De-register a Handset

68

Change the PIN Code for Base

69

Reset Factory Default

70

Appendix: Default Settings

71

Warranty Information

72

Notes for operation in New Zealand

The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If this occurs, the problem should not be referred to the Telecom Faults service.

This equipment shall not be set to make automatic calls to the Telecom “111” Emergency Service. This equipment may not provide for the effective hand-over of a call to another device connected to the same line.

REN (RN for New Zealand)

The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1 telephone to your telephone line. A standard telephone line has a maximum REN capacity of 3 (RN of 5). It is possible to connect 3(5) devices with a REN of 1 (RN of 1) with no degradation to the product’s performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all.

Caller ID

Customers using non Telecom toll services should not use the dial back feature for local calls as this will incur a charge only the 7 digit number should be dialled. Some of the CID services listed may not be available in New Zealand

5 of 72

6 of 72

Image 3
Contents MI40 User guide Answering Machine Using the Phone BookAdditional Features Caller IDAppendix Default Settings Warranty Information Using Additional Cordless HandsetsSafety Information Getting StartedUnpacking Your Telephone LCD Display on the HandsetIcon Name Description Basic Steps to Install Battery Level IndicationCharging the Handset Redial Menu Menu OverviewPhonebook Menu Call Log MenuUsing Traditional Dialling Basic OperationsTo End a Call Using Pre-Dialling Using Quick DiallingUsing Direct Dialling Save the Redial Number in the Phonebook Using Last Number Re-Dialling functionRedial the Last Dialled Number by Using Pre-dialling Redial the Last Dialled NumberDelete a Redial Number When the handset is on the base unit, lift the handsetWhen the handset is not on the base unit Adjusting the Handset Ringing VolumeMicrophone Mute / Un-mute Adjusting the Receiver VolumeHandsfree Operation Using the Handsfree Speaker Using a Headset Not suppliedReviewing the Phonebook Using the Phone BookLow Power Mode Storing an EntryDialling a number from Phonebook Deleting a Phonebook EntryVIP Ringing Melody Reviewing the Call Log Caller IDCall Waiting Caller ID Call LogCall Back from the Call Log Answering MachineSaving the CID record into phonebook Deleting a CID RecordRecording OGM Answering ModeChanging Answering Mode Outgoing Message OGMMemo Deleting the customized OGMAnswering Machine On / Off Answering Machine Quick OFFRecording ICM Playing MemoDeleting Memo Incoming Message ICMRing Delay Playing ICMDeleting ICM Alert Tone Message LengthSpeaker Filtering Exempt Call ScreeningOFF ALLRemote Access Code Block the BlockerSOS Code Remote Access to the Answering Machine Remote Access ShortcutsRemote Access Responses Reviewing Network Services Additional FeaturesNetwork Services Adding a new Network ServiceDialling out the Service Number Editing Network Service NumberDelete a Network Service Following call barring options can be selected FeaturesPrefix Call BarringRinger Melody for Internal Calls Ringer Melody for External CallsCharging Ringing Volume for BaseBase Ringer Melody for External Calls Alert TonesHandset Name Out of Range WarningAuto Answering Recall TimingBacklit LCD Call TimerBase Selection Using Additional Cordless HandsetsDelete All Records RegistrationTo end intercom call Or Use Pre-DiallingDe-register a Handset Conference CallRoom Monitoring MonitorChange the PIN Code for Base Reset Factory DefaultWarranty Information Appendix Default Settings