ClearOne comm 900, 600 user manual Specifications, Dimensions

Page 41

76

Specifications

Dimensions

Mixer (WxDxH) 17" x 7.5" x 2"

(43.2 cm x 19.1 cm x 5.1 cm)

RF Controller (WxDxH) 10.5" x 4.5" x 2.75"

Microphone Pod

Diameter 7" (17.8 cm)

Height 1.5" (3.8 cm)

Weight

Mixer 4.5 lb (2.04 kg)

RF Controller 2.0 lb (.91 kg)

Microphone Pod 1.1 lb (.5 kg)

Environmental

Operating Temperature: 32º to 122º F

0º to 50º C

Power Supply

Primary Voltage: 100 to 240 VAC Auto sensing 50-60 Hz

Audio Performance

Conditions: Unless otherwise specified, all measurements are performed with a

22 Hz to 15 kHz BW limit (no weighting)

Microphone Pod

Coverage: 360 degrees

Connection: RJ-45 with Cat. 5,

Link In/Out Ports

Max Distance from Base Mixer:

50' (RAV 900), 75' (RAV 600)

Frequency Response: 60 Hz - 14 kHz (+/-1dB)

THD+N: < 0.08% (-45dBu input @ 1 kHz)

Sensitivity: -45 dBu

Input Level: -6 dBu for 1 kHz 94 dBSPL microphone input

Appendix — Specifications

Dynamic Range: > 65dB

Line Input

Connection: Unbalanced RCA

Gain: -10 dBu nominal, adjustable from -14 dB to +18 dB

Nominal Level: -10 dBu

Maximum Level: +9 dBu

Impedance: > 10 kOhm

Line Output

Connection: Unbalanced RCA

Nominal Level: -10 dBu, adjustable from -14 dB to +18 dB

Maximum Level: +9 dBu

Frequency Response: 40 Hz - 15 kHz (+/-1dB)

Dynamic Range: > 80 dB

THD+N: < 0.02% (+6 dBu input @1 kHz)

Playback/Record Input

Connection: Unbalanced RCA

Gain: -10 dBu nominal, adjustable from -14 dB to +18 dB

Nominal Level: -10 dBu

Maximum Level: +9 dBu

Impedance: > 10 kOhm

Playback/Record Output

Connection: Unbalanced RCA

Nominal Level: -10 dBu, adjustable from -14 dB to +18 dB

Maximum Level: +9 dBu

Frequency Response: 40 Hz - 15 kHz (+/-1dB)

Dynamic Range: > 80 dB

THD+N: < 0.02% (+6 dBu input @1 kHz)

Appendix — Specifications

Loudspeaker

Connection: Push terminals with left and right

Power: 10 Watts into 8 Ohm load

Impedance: 8 Ohm

Frequency Response: 60 Hz - 15 kHz (+/-1 dB)

Dynamic Range: > 80 dB

THD+N: < 0.5% (+5 dBu line input @1 kHz)

Output Level: 90 dBSPL output @ 1 meter

Mixer

AEC tail time: 128 ms

Adaptive noise cancellation: (6 - 18 dB)

Gating: Adaptive ambient, 1st mic priority, look ahead gating, NOM attenuation

Telephone Interface

Conditions: All measurements taken with ALC disabled

Connection: RJ-11 (Set and Line Jacks)

Tail Time: 30 ms

Frequency Response: 250 Hz to 3.3 kHz (+/-1 dB)

THD+N: < 0.2% (+7 dBu line input @1 kHz)

Dynamic Range: > 60 dB

Communication I/O

10/100 Ethernet Control Port:

RJ-45 with LED indicators for link, duplex and activity status.

RS-232 Control Port:

DB9 female 9,600/19,200/38,400/57,600 (default)/115,200

Baud rate: 8 bits, 1 stop, no parity Hardware flow control on (default)/off

VISCA Camera Port

DIN, 9600 baud, No Flow Control

USB 1.1 Configuration Port

Slave Port

77

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 41
Contents Page Table of Contents Introduction RAV 600/900 Services and supportProduct returns UnpackingMixer Product OverviewRF Radio Frequency Controller Basic Room Design Microphone PodsBasic Room Design for RAV Speakers ceiling- or wall-mountInstallation Overview Network Information System Requirements for RAV-WareConnecting the RAV Audio conferencing To set up audio conferencingBasic Connections Attach the external antenna and turn it it is upright Auxiliary Devices Connecting video codecs, amplifiers and sound cardsTo connect to a video codec To connect to a sound cardConnecting PTZ cameras Connecting VCRs and DVD playersConnecting for serial control Connecting for USB controlTo connect to a digital phone Digital phonesRAV-Ware Software Configuration Introduction Install RAV-WareGetting started with RAV-Ware RAV-Ware overviewRAV-Ware files RAV-Ware connectionsNetwork Find Configuring System SettingsCommunication Settings Telephone Settings Regional SettingsMicrophones Customizing RAV ComponentsMixer Console Effects of using an external amplifierLoudspeakers Line Input and Output Preconfigured video codecs, amplifiers and sound cardsAdjusting Line Input/Output settings Record and Playback Preconfigured record/playback devicesAdjusting Record/Playback settings Camera Controls Setting camera presetsDialer and Phonebook Usage PhonebookDialer Event Log Advanced FeaturesSystem Checks Device Toolbox Editor Error MessagesFirmware upgrades Using the RAV Managing Calls Using the ControllerProgramming Phone Preferences Using the Phonebook from the RF ControllerAccessing the menu Configuration Adjusting the SettingsTo perform RF radio test To select a frequencyTo enter flash duration To change LCD contrastTo check the RAV version To view the IP addressWeb Interface Dial Accessing the web interfaceOverview To download log To open event logTo clear log To open the system checks System CheckLog Out Appendix Troubleshooting MaintenanceAudio ControllerPinouts SpeakersCamera pinouts GeneralDimensions SpecificationsCommand structure Serial CommandsConventions Groups and channelsMeter type definitions Serial command error codesRAV serial commands Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableAEC Acoustic Echo Canceller enable/ disable AD Auto Disconnect Enable/ DisableAecref Acoustic Echo Cancellation Reference Aconn Audible Connect / Disconnect IndicationCamctrlmode Camera Control Port Mode Batterylvl Battery LevelBaud Baud Rate Calldur Call DurationCampresetset Camera Preset Setup Campreset Camera PresetCamflow Camera Control Flow Control Cammove Move the CameraCamswitchlag Camera Switch Time Lag CAMPRESETSET2 Camera Preset SetupCamposition Camera Position Camtrack Camera TrackCleareffect Clear Effect Wide Band Telco Emulation Default Default The UnitClock Clock Set Country Country SelectionDid Device ID Device Device Identification LabelDial Dtmf Dialing Enetaddr Ethernet port IP address Enetgate Ethernet default Gateway addressEnetdhcp Ethernet Dhcp Selection Enetdnsa Ethernet DNS Server addressesGain Gain Adjustment Eqsel Equalization EnableEQ Equalization Flow Flow ControlHook Hook Flash Greport Gate ReportHookd Hook Flash Duration Label LabelLVL Level Lvlreporten Level Report EnableLvlreport Level Report Manufacturer Manufacturer Identification LabelNcsel Noise Cancellation Select Miccampreset Mic Camera PresetMtrx Matrix Routing Mute MutePhonebookadd Adds an Entry to the Phonebook Pbdial Dial a PB Entry by NamePhonebookcnt Queries the Number of Entries in the Phonebook Phonebookdel Deletes an Entry to the PhonebookRedial Dial the last number again Reset ResetRffreq RF Frequency Selection Ring Ring IndicationRingerlvl Audible Ring Level Silenceprst Silence Camera PresetRingersel Audible Ring Melody Selection Ringertest Audible Ring Melody TestSyschecks System Checks Stereomix Sets the Input to be a Stereo MixSysresult System Check Result 112Telcolvlctrl Telco TX Level Control Enable/ Disable TE Telco EnableVolume Volume Adjustment UID Unit IDCompliance Electrical Safety AdvisoryFCC Part 15/ICES-003 Compliance FCC Part 68 ComplianceEC Declaration of Conformity European ComplianceIndex
Related manuals
Manual 63 pages 47.95 Kb

600, 900 specifications

ClearOne Comm 900,600 is a cutting-edge communication platform designed to enhance audio and video conferencing experiences in both corporate and educational environments. With its advanced technology and user-friendly interface, ClearOne Comm 900,600 addresses the increasing demand for seamless collaboration in a hybrid work scenario.

One of the standout features of the ClearOne Comm 900,600 is its exceptional audio quality. Utilizing advanced beamforming microphone technology, the system captures sound from multiple directions while minimizing background noise. This ensures that every participant in a conference call is heard clearly, regardless of their position in the room. The system also supports high-definition audio processing, delivering crystal-clear sound that enhances the overall communication experience.

The ClearOne Comm 900,600 is equipped with state-of-the-art video capabilities as well, making it suitable for various applications. It supports high-definition video resolutions, enabling users to engage with their audience visually without compromising quality. The system is compatible with various video conferencing applications, ensuring flexibility for users who may prefer specific software solutions.

Another significant characteristic of the ClearOne Comm 900,600 is its scalability. Organizations can easily expand the system according to their needs. Whether it's a small meeting room or a large auditorium, the Comm 900,600 can be configured to accommodate various room sizes and setups. It provides multiple connection options, including USB and HDMI, making it easy to integrate with existing equipment.

Additionally, the ClearOne Comm 900,600 boasts a user-friendly interface that simplifies operation for all participants. Its intuitive controls ensure that even those unfamiliar with technology can navigate the system effortlessly. This focus on usability promotes a smooth and efficient meeting environment, which is essential in today’s fast-paced work culture.

Lastly, the ClearOne Comm 900,600 features robust security measures to protect sensitive data. It employs encryption protocols to safeguard communications while also adhering to industry standards for data protection. This ensures that organizations can conduct confidential discussions without concern for unauthorized access.

In conclusion, the ClearOne Comm 900,600 is an innovative solution for modern communication needs, offering advanced audio and video technologies, scalability, user-friendly operation, and strong security features. It is an essential tool for promoting effective collaboration in any organization.