ClearOne comm 900, 600 user manual Installation Overview

Page 7

8

Introduction — Basic Room Design

Introduction— Installation Overview

 

9

 

Loudspeakers

Ceiling-mount loudspeakers

For best performance, ceiling loudspeakers should be installed directly above the microphone pods. If you have a RAV 900 with three mic pods, install the ceiling loudspeakers above the first and third mic pods. The ceiling speakers must be set to 8 Ohms. Please refer to the Bose user manual for instructions.

Ceiling Speakers

Ceiling Speakers

Installation Overview

Read the user manual

Please read through the RAV Quick Start Guide and print user manual to familiarize yourself with the RAV system. Refer to the Help file in RAV-Ware for information on the software. Read through all requirements and safety information to be sure you set up and configure your RAV correctly.

Make sure your network is ready

Review all system requirements. Then check with your network administrator to be sure your network meets all the RAV requirements.

Connect cables

Wall-mount loudspeakers

Place the left channel loudspeaker on the left side of the room and the right channel loudspeaker on the right. (Refer to the label on the back of each loudspeaker.) Make sure the back of each loudspeaker is parallel to the front wall.

Figure 1.7 Recommended ceiling-mount speaker placement

RAV 600

Loudspeaker

6'

6'

Loudspeaker

Figure 1.8 Recommended wall-mount speaker placement

Connect cables. If you are planning on using the RAV for web or videoconferencing, you’ll need to connect peripheral equipment. See pages 14–22.

Install software

Install RAV-Ware and then use to adjust sound levels and to configure settings for additional equipment such as a video codec or a recording device. See pages 26–49.

Begin using

Use the controller to answer and make calls. See pages 52–61.

For best controller performance

Do not install the RAV mixer in a metal cabinet unless you are using the remote antenna accessory. Part number 910-153-050.

Keep the mixer within line of sight of the controller, such as on the top of a credenza.

Ensure antenna is connected to the back of the mixer and is pointed up.

If installing the mixer in an equipment rack, make sure it is placed at or near the top of the rack.

For best audio performance

Use the provided cables.

Do not move microphones while on a call.

Speak at a normal conversation level and direct your voice toward the microphones.

Do not place microphones next to fans, projectors or computers.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 7
Contents Page Table of Contents Introduction Unpacking Services and supportRAV 600/900 Product returnsRF Radio Frequency Controller Product OverviewMixer Speakers ceiling- or wall-mount Microphone PodsBasic Room Design Basic Room Design for RAVInstallation Overview Network Information System Requirements for RAV-WareConnecting the RAV Basic Connections To set up audio conferencingAudio conferencing Attach the external antenna and turn it it is upright To connect to a sound card Connecting video codecs, amplifiers and sound cardsAuxiliary Devices To connect to a video codecConnecting for USB control Connecting VCRs and DVD playersConnecting PTZ cameras Connecting for serial controlTo connect to a digital phone Digital phonesRAV-Ware Software Configuration RAV-Ware overview Install RAV-WareIntroduction Getting started with RAV-WareRAV-Ware files RAV-Ware connectionsCommunication Settings Configuring System SettingsNetwork Find Telephone Settings Regional SettingsMicrophones Customizing RAV ComponentsLoudspeakers Effects of using an external amplifierMixer Console Adjusting Line Input/Output settings Preconfigured video codecs, amplifiers and sound cardsLine Input and Output Adjusting Record/Playback settings Preconfigured record/playback devicesRecord and Playback Phonebook Setting camera presetsCamera Controls Dialer and Phonebook UsageDialer System Checks Advanced FeaturesEvent Log Firmware upgrades Error MessagesDevice Toolbox Editor Using the RAV Managing Calls Using the ControllerAccessing the menu Using the Phonebook from the RF ControllerProgramming Phone Preferences Configuration Adjusting the SettingsTo change LCD contrast To select a frequencyTo perform RF radio test To enter flash durationTo check the RAV version To view the IP addressWeb Interface Overview Accessing the web interfaceDial To clear log To open event logTo download log Log Out System CheckTo open the system checks Appendix Controller MaintenanceTroubleshooting AudioGeneral SpeakersPinouts Camera pinoutsDimensions SpecificationsGroups and channels Serial CommandsCommand structure ConventionsRAV serial commands Serial command error codesMeter type definitions Aarings Number of Rings to Auto Answer On AA Auto Answer Enable/ DisableAconn Audible Connect / Disconnect Indication AD Auto Disconnect Enable/ DisableAEC Acoustic Echo Canceller enable/ disable Aecref Acoustic Echo Cancellation ReferenceCalldur Call Duration Batterylvl Battery LevelCamctrlmode Camera Control Port Mode Baud Baud RateCammove Move the Camera Campreset Camera PresetCampresetset Camera Preset Setup Camflow Camera Control Flow ControlCamtrack Camera Track CAMPRESETSET2 Camera Preset SetupCamswitchlag Camera Switch Time Lag Camposition Camera PositionCountry Country Selection Default Default The UnitCleareffect Clear Effect Wide Band Telco Emulation Clock Clock SetDial Dtmf Dialing Device Device Identification LabelDid Device ID Enetdnsa Ethernet DNS Server addresses Enetgate Ethernet default Gateway addressEnetaddr Ethernet port IP address Enetdhcp Ethernet Dhcp SelectionFlow Flow Control Eqsel Equalization EnableGain Gain Adjustment EQ EqualizationLabel Label Greport Gate ReportHook Hook Flash Hookd Hook Flash DurationManufacturer Manufacturer Identification Label Lvlreporten Level Report EnableLVL Level Lvlreport Level ReportMute Mute Miccampreset Mic Camera PresetNcsel Noise Cancellation Select Mtrx Matrix RoutingPhonebookdel Deletes an Entry to the Phonebook Pbdial Dial a PB Entry by NamePhonebookadd Adds an Entry to the Phonebook Phonebookcnt Queries the Number of Entries in the PhonebookRing Ring Indication Reset ResetRedial Dial the last number again Rffreq RF Frequency SelectionRingertest Audible Ring Melody Test Silenceprst Silence Camera PresetRingerlvl Audible Ring Level Ringersel Audible Ring Melody Selection112 Stereomix Sets the Input to be a Stereo MixSyschecks System Checks Sysresult System Check ResultUID Unit ID TE Telco EnableTelcolvlctrl Telco TX Level Control Enable/ Disable Volume Volume AdjustmentFCC Part 68 Compliance Electrical Safety AdvisoryCompliance FCC Part 15/ICES-003 ComplianceEC Declaration of Conformity European ComplianceIndex
Related manuals
Manual 63 pages 47.95 Kb

600, 900 specifications

ClearOne Comm 900,600 is a cutting-edge communication platform designed to enhance audio and video conferencing experiences in both corporate and educational environments. With its advanced technology and user-friendly interface, ClearOne Comm 900,600 addresses the increasing demand for seamless collaboration in a hybrid work scenario.

One of the standout features of the ClearOne Comm 900,600 is its exceptional audio quality. Utilizing advanced beamforming microphone technology, the system captures sound from multiple directions while minimizing background noise. This ensures that every participant in a conference call is heard clearly, regardless of their position in the room. The system also supports high-definition audio processing, delivering crystal-clear sound that enhances the overall communication experience.

The ClearOne Comm 900,600 is equipped with state-of-the-art video capabilities as well, making it suitable for various applications. It supports high-definition video resolutions, enabling users to engage with their audience visually without compromising quality. The system is compatible with various video conferencing applications, ensuring flexibility for users who may prefer specific software solutions.

Another significant characteristic of the ClearOne Comm 900,600 is its scalability. Organizations can easily expand the system according to their needs. Whether it's a small meeting room or a large auditorium, the Comm 900,600 can be configured to accommodate various room sizes and setups. It provides multiple connection options, including USB and HDMI, making it easy to integrate with existing equipment.

Additionally, the ClearOne Comm 900,600 boasts a user-friendly interface that simplifies operation for all participants. Its intuitive controls ensure that even those unfamiliar with technology can navigate the system effortlessly. This focus on usability promotes a smooth and efficient meeting environment, which is essential in today’s fast-paced work culture.

Lastly, the ClearOne Comm 900,600 features robust security measures to protect sensitive data. It employs encryption protocols to safeguard communications while also adhering to industry standards for data protection. This ensures that organizations can conduct confidential discussions without concern for unauthorized access.

In conclusion, the ClearOne Comm 900,600 is an innovative solution for modern communication needs, offering advanced audio and video technologies, scalability, user-friendly operation, and strong security features. It is an essential tool for promoting effective collaboration in any organization.