Talkswitch TS-600 Configure the Outside Line Access Code, Extensions with Direct Line Access

Page 10

T S - 6 0 0 U S E R G U I D E

CONFIGURE THE OUTSIDE LINE ACCESS CODE

The outside line access code is dialed prior to any number over 6 digits stored in the directory, speed dial buttons, or the call log. A stored number with 6 or fewer digits is considered an internal number.

The outside line access code is not dialed for an internal call. A 3 second pause is inserted automatically between the outside line access code and the phone number.

Use Save to End

9

#= DLA Mode Enable Enter Access Code

Extensions with Direct Line Access

Direct Line Access allows you to access the outside phone lines directly, without having to enter a line access code. If your TalkSwitch extension is programmed for Direct Line Access, enter # as your line access code. This will ensure that features and dialing operate properly for your extension. Refer to your TalkSwitch programming guide for more information.

To enter outside line access code:

1.

Press the

M E N U

button followed by

2 .

2.

Enter your outside line access code or

# if your extension is configured for

 

Direct Line Access.

 

 

3.

Press the

S A V E

button to store the access code.

Selecting ring tone

You can select one of four ring tones for this telephone:

1. Press the M E N U button followed by 3 .

2.The phone rings with Ring Tone 1 for about 2 seconds.

Use Save to End

Use S/T Enter to Select 1 = Ring tone 1

2 = Ring tone 2

3 = Ring tone 3

4 = Ring tone 4

3. Press the

S A V E

button to select Ring Tone 1; or

4. Press the S button or the T button to select another ring tone.

5. After the end of the desired ring tone, press the

S A V E

button to select it.

Adjusting the display angle

You can optimize the LCD display by adjusting the viewing angle. To adjust the LCD viewing angle, move the rear edge of the LCD module up or down.

6

W W W.T A L K S W I T C H . C O M

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Talkswitch TS-600 Telephone TalkSwitch is a division of Centrepoint Technologies Inc Table of Contents Page Important Safety Instructions Installing Your PhoneIntroduction W.T a L K S W I T C H . C O M Connecting the handset Part ChecklistInstallation Connecting power through cord adapterConnecting power directly from the AC adapter Wall MountingSetting UP Your TS-600 Phone Configure Area CodesAdjusting the display angle Configure the Outside Line Access CodeExtensions with Direct Line Access Selecting ring toneAdjusting the Headset Receiver Volume Adjusting the Display ContrastAdjusting the Handset Receiver Volume Adjusting Speakerphone Receiver VolumeUsing Your Phone Overview of the TS-600 PhoneKEY Label Usage Menus and Softkeys Phone DisplayMaking a Call Redialing Calls Receiving CallsCall Waiting and Queued Calls Hanging UP a CallPutting a Call on Hold Transferring a CallTo retrieve a call that has been parked Conferencing CallsPicking UP a Call OVERHEAD, Intercom and Group Paging Send a Call to Voicemail Ring Once FeatureDo not Disturb Check VoicemailsViewing the Caller ID List Accessing the Call LOGCalling Back a Number from the Call LOG Deleting a Call from the Call LOG Using ONE-TOUCH Speed DialsUsing the Phone Directory Searching Telephone Numbers in the DirectoryProgramming a NEW Phone Number Deleting Entries in the DirectoryWhile reviewing the call Log Saving a CALLER’S Name and Number Troubleshooting Maintenance InformationResetting Your TELEPHONE’S Programming Phone DOESN’T Ring Reset to Factory DefaultsBlank Screen No Dial ToneMessage Waiting Count does not Work Problems DialingHandset DOESN’T Work CAN’T Receive ON-HOOK Intercom CallsLimited Warranty For Products Purchased in the U.S. or Canada Connection and USE with the Nationwide Telephone Network FCC Registration and Repair InformationRepair Instructions Interference Information Part 15 of FCC Rules
Top Page Image Contents