Siemens NI-1200 Programming Requirements, Switching System National Isdn Compliance Issues

Page 7

Issue 5, June 1988

Programming Requirements

For the Optiset terminal to operate as described in this guide, il must have been programmed with at least the following features:

•Line Hold Mode

•Off-hook answers any alerting call appearance

•Menu Active

•One Feature Key per Line Appearance

•Feature Keys for key operation of the following features:

-Conference

•Transfer

-Drop Last Party (Conference)

-Speed Dial

•Redial

-Hold

-Preview

-Connect

•Disconnect

•Speaker Key

•Fast Transfer active

If your terminal does not operate as described in this guide, check with the person responsible for installing and setting up your terminal to be sure your terminal has been programmed for these reqUired features; or refer to document 1275-00050, Optiset NI­ 1200 National ISDN Desktop Terminal Installation, Setup, and Programming Guide.

Switching System National ISDN Compliance Issues

The instructions in this guide are written for an Optiset terminal served by a switching system that complies with National ISDN (N!)

2

1275-00030

Issue 5, June 1999

standards. This includes the EWSD@ switching system. The Optiset terminal also can be used, with certain limitations, when connected to a switching system that Is not fully NI-compliant. Switch-based or combined local/switch-based features may operate somewhat differently than described in this guide because of variations in the compliance of the switching system to Nl standards.

In particular, Transfer procedures may vary from one switching system to another. In this guide, the Transfer feature is invoked by pressing the Transfer feature key (or selecting the Transfer menu option) while the call to be transferred is active, dialing the number of the party to receive the call, and then simply hanging up to complete the transfer. However, with some switching systems, one of the following procedures must be used instead to transfer an active call:

•Press the Transfer feature key; dial the number of the party to receive the call; if you wish, announce the call to the receiving party; and then press the Transfer feature key again to connect the two parties.

•Press the Conference feature key; dial the number of the party to receive the call; if you wish, announce the call to the receiving party; and then press the Transfer feature key to disconnect yourself and connect the other two parties.

•Press the Conference feature key; dial the number of the party to receive the call; if you wish, announce the call to the receiving party; press the Conference feature key again to establish a 3-way conference; and then hang up to leave the other 2 parties connected.

In addition, the way your Optiset terminal requests certain sWitch­ based features may result in visual and audible indicators that differ slightly from those described in this guide. However, the operation of those features should be substantially the same, and the Instructions in this guide should suffice to direct you in the use of those features.

1275-00030

3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents OPTISET@ NI-1200 Issue Date Issued Issue InformationContents Summary of Issue EnhancementsAlternative Call Operations Menu Trees LJ~UJ Introducing Your OptisetProgramming Requirements Switching System National Isdn Compliance IssuesIssue 6, June Microphone Volume UpNolume Down KeysOptional Headset Multiline Hunt Group Types of Service SupportedBasic Electronic Key Telephone Service Baaic Isdn Terminal1275-00030 Basic Call Operations Place a Call Using the Handset Procedure DisplayIDial 1555-5555 THU FEB 04, 99 0943 AM 555-5555 01 00Ithu FEB 04, 99 0943 ~~ 555-5555 010000Retrieve call line 1? 555-5555Answer call? 1I0ld?555-5555 010012 555-55!J5 Ilold?5SS-SS55 01 00 Hold?555-5555 010522 Cancel Conference? 555-5565Ringing Ringing IconferenceIDrop last party? Cancel Conference?Conference? Alternative Call Operations 1275·00030 1275·00030 Illue 5, June Hold a Call Clear a CaliOn Hold88U8 5, June Transfer a Call Ssue 5, June Password Prompt USER-CONTROLLED Terminal SettingsAssign, Change, or Delete Password Enter passwordPhone configuration Menu Verify new passwordPhone configuration Password?Audio settings Ringer pitch? Configure phone?Initial settings? Audio settings?Speaker Loudness Audio settings Handset loudness?Key clicks Orf Turn on key clicks? Audio settings Speaker loudness?Audio settings Ringer loudness? Key click setting? THU FEB 04, 99 0955 AMMuted ring selected Select attention tone? Audio settings Busy alerting type?Busy Alerting Type Procedure Display 1i ck Sett i ng?THU FEB 04 0955 AM Local featuresMenu overlay delay?O Local Features?Line preview mode Change to line hold? Loca I features Speaker control?Speaker is enabled Oisable speaker? Line hold mode Change to line preview?Menu Setting ProcedureDisplay Mellll is demand Dilly Disable menu mode?Menu Is disabled Activate menu mode? Loca I features Menu setting?Hot Keypad ProcedureDisplay Phone configuration menu 1 ­ Initial settings?Hot keypad mode Select composed dial? Composed dial mode I Activate menu mode?Speaker Double talk Double talk? Loca I features Hot keypad setting1Loca I features Speaker setting? Speaker single Talk Single talk? Loca I features0 to 9 seconds Enter call display time Loca 1 features Incoming call disp?Incoming Call Display ProcedureDisplay Off Hook Result Procedure DisplayLocal features Menu overlay delay? Fast transfer? Loca features Off hook result?Phone configuration menu Initial settings? Local features? Loca I features Off hook result?Use the .J and I dialog Local features Fast transfer?Press the II dialog key to select the local Features menu Use a combination of the .JTo change the Fast Transfer Local features Autoanswer mute?Press the t/ dialog key to select the Local Features menu THU fEB 64, 99 6955 AMMo 05 Day 22 Year Set date?Mo XX Day XX Year Enter DateOptiset Terminal Used AS AN Ekts Phone 1275·00030 1275-00030 Hold ConferencelTransfer Call AppearanceIntercom Headset Operation Controlling the Headset Using the PlugPlugging Headset Controlling the Headset Using Keys or Menu Options Features Conference/Large Conference 1275·00030 Download Active Call Inspection Local Feature InspectionSystem Feature nspection Idle Line InspectionMake Busy Line Status/Speed DialMute 188ue 5, June 100 1275-00030 UUS Answering Redial Menu TreesOutgoing Call· Dialing Incoming Call AlertingAuto Callback Call Alerting Outgoing Call OffhookRelease this call? Retrieve line x? Transfer call? Clear download message? Call Log AccessedIndex CACH,9 Ssue 5, JuneMenu Trees TA-TAPI Issue 5, June

NI-1200 specifications

The Siemens NI-1200 is a versatile and innovative device designed for a wide range of automation and control applications. As part of Siemens' extensive portfolio, the NI-1200 showcases cutting-edge technologies and features that enhance operational efficiency and flexibility in industrial environments.

One of the main features of the NI-1200 is its robust processing power. With a high-performance processor, the device is capable of handling complex automation tasks in real-time. This enables seamless integration with various automation components, allowing for greater control and monitoring of processes.

The NI-1200 is equipped with advanced communication capabilities, supporting various industrial communication protocols such as Ethernet/IP, Profinet, and Modbus. This extensive connectivity makes it easy for the device to interface with other systems, sensors, and actuators, promoting interoperability and data exchange across different platforms.

In terms of data handling, the NI-1200 offers rich data logging and analysis features. Users can collect, store, and analyze data from different sources, which is essential for process optimization and troubleshooting. This capability ensures that organizations can make informed decisions based on accurate and timely data, ultimately leading to improved productivity and reduced downtime.

The device is also designed with scalability in mind. Whether organizations are looking to implement a small-scale solution or require extensive systems integration, the NI-1200 can adapt to changing needs. Its modular design allows for easy upgrades and expansions, catering to future growth and evolving technology landscapes.

Another key characteristic of the Siemens NI-1200 is its user-friendly interface. The device features an intuitive graphical user interface (GUI) that simplifies configuration and monitoring tasks. This ease of use reduces the learning curve for operators and maintenance personnel, enhancing overall productivity.

Additionally, the NI-1200 is built with durability and reliability in mind, suitable for harsh industrial environments. It complies with international standards for safety and environmental conditions, making it a dependable choice for various applications, including manufacturing, process control, and building automation.

In summary, the Siemens NI-1200 is a powerful and feature-rich automation device that stands out for its processing capabilities, communication options, scalability, and user-friendly interface. Its combination of advanced technologies and robust characteristics makes it an ideal solution for organizations looking to enhance their automation and control processes. With the Siemens NI-1200, businesses can achieve greater efficiency, flexibility, and reliability in their operations.
Top Page Image Contents