BT 2150 manual Charge the handset battery For at least 16 hours

Page 16

SETTING UP

Charge the handset battery

3 for at least 16 hours

Before you use your Synergy 2150 for the first time, it is important to have the handset battery fully charged. We recommend that you leave the Synergy 2150 on charge for at least 16 hours.

Place the handset on the base. The red charging light comes on. The handset should come pre-registered to the base station as HS1 and this is shown in the top right corner of the display.

The battery symbol is also shown. It flashes during charging. Once the handset is fully charged, the display shows a full battery symbol.

Battery levels

0% 50 -100%

(flashing)

0-50% 100%

Battery low warning.

If the handset battery symbol is empty and flashing, and you hear a warning beep every 10 seconds, you will need to recharge your handset before you can use it.

Battery performance

To keep your battery in the best condition, leave the handset off the base station for a few hours at a time (after the initial 16 hour charge).

After charging your Synergy handset for the first time, subsequent charging time for the battery is approximately

4-5 hours. Battery and case may become warm during charging. This is normal and not dangerous. Note: Once the handset is fully charged the red charging light will go off.

Under ideal conditions, the handset battery should give about 12 hours talktime (7 hours in handsfree mode) or 150 hours standby on a single charge.

Please note, however, that a new NiMH battery does not reach its full capacity until it has been in normal use for several days.

Please note that while the NiMH rechargeable battery can be expected to give years of service they do not last forever.

Their actual lifespan depends on how heavily they are used but over time, their capacity to recharge will begin to diminish and they will eventually need replacing.

11

Image 16

Contents User Guide Page Page Page At a glance SynergyBase Menu Structure Answering machine features Menu Structure for the Answering MachineThis guide Hints and tips boxesKey features Remote access Introduction Building up a phone systemUnpacking your Synergy2150 For your recordsSafety instructions Setting up Connect the power cableInstall the rechargeable Battery in the handset Plan the location of your SynergyCharge the handset battery For at least 16 hours Customer Helpline Connect the telephone line cordUsing your Synergy 2150 telephone Making and receiving callsCall monitoring To receive a callTo use handsfree Caller displayTo adjust the earpiece volume SecrecyTo redial the last number To redial one of the last 5 numbersGo to Tone Dialling modeGo back Using the notepad To use the recall buttonTo store a notepad number To view and dial a notepad numberUsing the phonebook To store a notepad number in the phonebookPhone book New entryTo store a name and number in the phonebook To enter a pause in a stored numberTo dial a number stored in the phonebook To confirm deletionUsing your Synergy 2150 answering machine To set the base speaker volumePlease note To set the day and timeSetting the answer mode To record your own announcement To delete an announcementTo adjust the base speaker volume To turn the handset speaker on or offTo adjust the handset speaker volume To set your security PIN for remote accessMessage playback Memory fullTo play your messages To skip, play, pause and delete your messagesMessage To delete old messagesTo record a memo To use Call ScreeningRemote access To turn answering machine on via remote accessRemote access quick guide Using Caller Display BT Select ServicesCall indications To view stored numbers To save a callerÕs number into the phone bookUsing the VIP feature Call WaitingTo delete old numbers To store a VIP numberOther services To use Call WaitingTo adjust the handset ringer volume Optional SettingsTo adjust the handset ringer melody To switch the keytones off and on To set a different language for the displayBase ringer Base station settingsMelody Base setting HS PriorityRing To set the handset priority To change the base station PINCall barring Show baseBase name To set call barringSet new name To change the base station nameRegistration Using additional handsetsTo register a handset Internal Remove HSTo de-register a handset To call another handsetTo hold a three-way conversation IntOperating with additional base stations To register your handset to Another base stationTo change the dialling mode SettingTo change the network connection Pstn prefix To enter a Pstn pre-fix codeGeneral ServiceIf you have to return your Synergy Help Emergency callsCheck that Technical information Technical specification Index DectPIN VIP 610384