Beko BD 220 user manual Pause time selection, Reset to factory default settings, Quick Reset

Page 26

Pause time selection

If your phone is intended to be connected to a PABX, the PAUSE duration may be required. Your phone has a 4 preset Pause time as: 1, 1.5, 2 and 3 sec.

1.Press OK/Menu button. PHONEBOOK is displayed.

2.Use DOWN button to scroll to BASE.

3.Press OK/Menu button.

4.Use DOWN button to scroll to the option PAUSE.

5.Press OK/Menu button. The display will show PAUSE: X (X= pause time 1 to 4).

6.Use UP or DOWN button to select your desired pause time.

7.Press OK/Menu button to confirm and exit to PAUSE.

8.Press TALK-OFF button to go back to the standby mode.

Reset to factory default settings

This feature will restore the default setting of your DECT phone. If you have lost your PIN code, the following procedure allows you to restore default setting on handset and base. But all the programming done earlier like setting the ringing volume, ringing melody, external call melody, clear the phonebook, clear the LNR, etc. will be defaulted.

1.Press OK/Menu button. PHONEBOOK is displayed.

2.Use DOWN button to scroll to BASE.

3.Press OK/Menu button.

4.Use DOWN button to scroll to the option DEFAULT.

5.Press OK/Menu button. The LCD shows PIN?.

6.Enter the base PIN number from the numeric keypad.

7.Press OK/Menu button to validate system default. The handset will lost SYNChronization to the base. The base will beep also indicating a successful default. After about 2 seconds, the Handset will beep and gain SYNC again to the base.

Note:

If you are using 2 or more handsets (multi handset operations), default one handset will take no effect on the other handset. But the base will always be defaulted no matter who among the handset will initiate the default setting.

Quick Reset

*If you have lost your PIN code, the following procedure allows you to restore default setting on handset and base.

1.Remove the batteries. Wait for 5 seconds. (Please note the base should be power on.). Then insert the battery again inside the handset compartment and watch closely the LCD.

(For this step, you can also do like this: a) Press and hold TALK-OFF key to power off the handset; b) Press TALK- OFF key again and watch closely the LCD.)

2.Press star key (*) on the handset keypad immediately when the handset is initiating (i.e. when the all the icons are showing on LCD.)

3.The LCD will display: DEFAULT.

4.Press the OK/Menu button. Wait for about 3 seconds.

5.Then Base will reset first followed by the handset. After the handset and base reset, the unit will go into the standby mode.

- 27 -

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Contents Display Earpiece/Receiver Talk-Off / Esc / PowerINT / Cancel Speaker phone / HandsfreeLCD Display on Handset Handsfree speaker is in useMenu Options Date / TimeQuick Reference Guide FunctionConnection and condition for use What is in the boxRadio signal between handset and base Choosing a site for the BaseEmergency calls Electrical SafetyCharging the batteries Starting UP Standby mode display DectPreparatory dialing pre-dial Using Your PhoneTo make and end calls Receiving external callsUsing Pause function Using MuteUsing Recall Flash Adjust the handset earpiece during a callFunction Using Phone BookSwitching your handset On or Off Out of range warningDialing a phone book entry To access phonebook via Menu optionReviewing the phonebook Deleting all entries in the phone book Editing an entry in the phone bookDeleting an entry in the phone book Caller ID To store a CID entry in the phonebook Deleting a CID recordVoice Mailbox Hot Key Call back from the calls listVoice Mail Box Message Waiting Review MessageSetting Base Ringer Volume Personalizing Your SettingSetting the handset ringer volume Selecting Base Ringer melodiesSetting Handset earpiece Speakerphone Volume Alert tonesKeypad lock Naming the HandsetLanguage selection Auto AnsweringRegistering a new handset Expanding Your Dect SystemAdding new handset On the baseCall Shuttle Register Another Dect GAP compatible HandsetMulti Handset Use Internal outgoing callsRegister Another Dect GAP compatible Base Three way conference callRegister another HM base to HM Handset Base SelectionChange PIN Code Advanced FeaturesProgramming De-registering a handsetPause time selection Reset to factory default settingsQuick Reset Default setting parameters Technical DetailsDialing type Pabx Access Code and Pause ? Do you need Recall Flash?USE in Business Do you need a PAUSE?Troubleshooting Guide Problems Possible Cause Action Taken
Top Page Image Contents