Audiovox GX2411ci Initial Setup, Setting the DAY and Time of the Base Unit, Tone / Pulse Setting

Page 14

GX2411ci English I/B ver. 09010A-1

1.Remove the battery compartment cover of the handset. Connect the rechargeable Ni-Cd battery as shown on Figure 10.

Handset

 

Battery

Insert the End of the

Compartment

Battery Pack Wire

RED Wire

BLACK Wire

(Figure 10)

2.Insert the Ni-Cd battery into the battery compartment of the handset.

3.Slide the battery compartment cover firmly in its closed position.

INITIAL SETUP

Before you can use your cordless telephone, the handset must be charged for at least 20 hours. See charging instruction on MAXIMIZING BATTERY LIFE section of this manual.

SETTING THE DAY AND TIME OF THE BASE UNIT

NOTE: The time set is used for time stamping the recorded message(s).

1.After 20 hours, lift the handset from the base unit.

2.Press the REMO button on the handset. The GX2411CI

will prompt “You have no new message. For help, press 9.” followed by a long beep. (Figure 11)

3.Press 2. The unit will prompt “Time is off. Enter new day.”

4.After hearing a long beep, enter the new day (Sunday = 1, Monday = 2, Tuesday = 3, etc.). The unit will then prompt “Enter new time.”

5.After hearing a long beep, enter the new hour (01-12).

6.After two beeps, enter the new minute (00-59).

7.After two beeps, press 1 for AM, or press 2 for PM. The unit will announce the new day and time followed by a long beep and will prompt “Please enter next command.”

8.Press the REMO button to exit the remote mode. Otherwise, the remote function will turn off automatically if not in use for 8 seconds.

TONE / PULSE SETTING

 

Select the appropriate dialing service by moving the T / P

 

(Tone / Pulse) switch on the bottom of the base unit:

 

∙

TONE for Tone service, or

T / P

∙

PULSE for Rotary service.

(Figure 12)

SETTING THE HANDSET RINGER

The handset ringer must be set to ring ON position in order that to ring when receiving an incoming call. See PROGRAMMING MODE section on page 26.

SETTING USER'S AREA CODE AND NEIGHBORING AREA CODE

In order to use callback function, the user's area code and neighboring area code must be programmed. Neighboring area code is optional. See PROGRAMMING MODE section on

13

09010A-1

OWNER’S MAN # GX2411ci VER. 09010A-1

PAGE: 13

English version

Page 13 Page 15
Image 14
Page 13 Page 15
Contents GX2411ci Important Service Information Carton ContentsImportant Safety Instructions Rbrc SealBattery Safety Instruction FCC / IC NoticeFCC Part IC Industry CanadaWarranty Statement Table of Contents CONTROLS’ Location and Function Troubleshooting ………..………………………………………Description Handset Controls Cordless TelephoneHandset Controls Answering System Base Unit Controls Base UnitSide View Bottom View Desktop USE Mounting PositionCode Function Wall USEWall Mounting No Standard Wall Jack Connecting the HeadsetBelt Clip Instruction Handset Battery Installation Power InstallationBase Unit Power Connection Tone / Pulse Setting Initial SetupSetting the DAY and Time of the Base Unit Setting the Handset RingerTelephone Operation After Hearing a Busy Tone When Placing a CallWhen the Handset is OFF the Base Unit and in Standby Mode If the Handset is on the Base UnitKey Storing Telephone Numbers Into Memory Dialing DirectoryStoring Telephone Numbers Into the Speed Dialing List Deleting Single Memory Location Deleting ALL Memory LocationManual Channel Scan Answering Machine OperationAuto Channel Scan To Turn Answer Mode OFF To Turn Answer Mode onPrevious Messages Playing MessagesSkipping Messages Stop Message PlaybackFrom the Handset Away From the Base Unit Erasing ALL Memo MessagesErasing OGM From the Handset In the Base Unit CradleCalling the GX2411CI from a Tone Phone Using the HandsetRemote Operation Voice Help MenuSetting Answer Mode to on Changing the PasswordSetting the DAY and Time Setting Answer Mode to OFFReceiving NEW Call Caller ID OperationIntroduction to Caller ID and Call Waiting ID Viewing Call Records and NEW Call RecordsCallback Option Deleting Single Call RecordDeleting ALL Call Records HOW to Change the Language Programming ModeSummary of Function Mode HOW to SET Cidcw on / OFFHOW to SET Time HOW to SET Callback NumberHOW to SET Ringer on / OFF HOW to Adjust the Contrast of LCD DisplayCall Waiting ID Operation LCD Display Symbols and MessageTalking Time and Channel Display Screen Shown MeaningDischarging Maximizing Battery LifeImproving Cordless Reception ChargingTechnical Information Troubleshooting Symptoms Possible Solution / CauseMemory Full 09010A-1 GX2411ci English I/B ver A-1
Top Page Image Contents