Audiovox GX2411ci Improving Cordless Reception, Maximizing Battery Life, Discharging, Charging

Page 29

GX2411ci English I/B ver. 09010A-1

11:10 AM 10/10 CALL# 03 234-567-8901

NO NAME

11:10 AM 10/10 CALL# 03

234-567-8901

 

 

 

JOHN SMITH

*

 

 

 

TALK

[ M ]

 

 

 

 

OUT OF RANGE

MSG WAIT ON

MSG

ALL:10 NEW:05

NO NAME

The Caller Name might not be available from the caller's area.

REPEAT CALL

This blinking * indicates that the Call record information comes multiple.

TALK

The handset is ON and ready for you to dial. [ M ] means that the volume level is medium.

OUT OF RANGE

The handset has tried to call but failed or the handset is moved out of range from the base unit in talk mode.

MSG WAIT ON

This means that your voice mail box has a new message right now.

MESSAGE WAITING MARK

The MSG mark means that your voice mail box has a new message.

IMPROVING CORDLESS RECEPTION

Follow these guidelines to improve cordless sound quality:

∙Select an area to install the GX2411CI where it is closest to the center of your home or office. This will improve the operating range of the unit.

∙Keep the GX2411CI base unit away from electrical equipment. Radio Frequency Interference (RFI) is sometimes generated by these appliances, which can cause a degradation in cordless reception.

∙Keep the handset batteries charged as much as possible. Weak handset batteries can limit the range of cordless operation.

MAXIMIZING BATTERY LIFE

Repeated use or recharge of Ni-Cd batteries without periodic full discharge results in reduced useable charge time. When you notice the usable charge duration decreasing, fully discharge the Ni-Cd battery and recharge as described:

DISCHARGING

1.Unplug the telephone line cord from the GX2411CI.

2.Make sure that the adapter is connected.

3.Lift the handset out of the base cradle.

4.Press the TALK button of the handset (IN USE LED indicator should light) and start discharging.

Once the BATT LOW LED indicator starts flashing, it means that the battery level is low. Let it fully discharge for 12 hour. Once the Ni-Cd battery is fully discharged, you may now charge the battery to its full capacity.

CHARGING

1.Make sure the adapter and telephone line cord is connected to the GX2411CI.

2.Place the handset on the base cradle. The CHARGE LED indicator of the base unit will light steadily.

3.Leave the handset charging on the base for 20 hours continuously to get a maximum charge.

09010A-1

28

OWNER’S MAN # GX2411ci VER. 09010A-1

PAGE: 28

English version

Page 28 Page 30
Image 29
Page 28 Page 30
Contents GX2411ci Carton Contents Important Service InformationRbrc Seal Important Safety InstructionsFCC / IC Notice Battery Safety InstructionIC Industry Canada FCC PartWarranty Statement Table of Contents Description Troubleshooting ………..………………………………………CONTROLS’ Location and Function Handset Controls Cordless TelephoneHandset Controls Answering System Base Unit Controls Base UnitSide View Bottom View Code Function Mounting PositionDesktop USE Wall USEWall Mounting No Standard Wall Jack Connecting the HeadsetBelt Clip Instruction Handset Battery Installation Power InstallationBase Unit Power Connection Setting the DAY and Time of the Base Unit Initial SetupTone / Pulse Setting Setting the Handset RingerWhen the Handset is OFF the Base Unit and in Standby Mode After Hearing a Busy Tone When Placing a CallTelephone Operation If the Handset is on the Base UnitKey Storing Telephone Numbers Into Memory Dialing DirectoryStoring Telephone Numbers Into the Speed Dialing List Deleting ALL Memory Location Deleting Single Memory LocationManual Channel Scan Answering Machine OperationAuto Channel Scan To Turn Answer Mode on To Turn Answer Mode OFFSkipping Messages Playing MessagesPrevious Messages Stop Message PlaybackErasing OGM Erasing ALL Memo MessagesFrom the Handset Away From the Base Unit From the Handset In the Base Unit CradleRemote Operation Using the HandsetCalling the GX2411CI from a Tone Phone Voice Help MenuSetting the DAY and Time Changing the PasswordSetting Answer Mode to on Setting Answer Mode to OFFIntroduction to Caller ID and Call Waiting ID Caller ID OperationReceiving NEW Call Viewing Call Records and NEW Call RecordsCallback Option Deleting Single Call RecordDeleting ALL Call Records Summary of Function Mode Programming ModeHOW to Change the Language HOW to SET Cidcw on / OFFHOW to SET Ringer on / OFF HOW to SET Callback NumberHOW to SET Time HOW to Adjust the Contrast of LCD DisplayTalking Time and Channel Display LCD Display Symbols and MessageCall Waiting ID Operation Screen Shown MeaningImproving Cordless Reception Maximizing Battery LifeDischarging ChargingTechnical Information Symptoms Possible Solution / Cause TroubleshootingMemory Full 09010A-1 GX2411ci English I/B ver A-1
Top Page Image Contents